• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

ZZP Modified rockers

Lsick7

Tofu Delivery Boy
I just bought a set of zzp modded 1.9 rockers second hand for real cheap. But, i just noticed they do not come with the modified pedestals. Am i completely screwed or what do i do?
 


Didn't know the modded 1.9's had modded pedestals too...I thought you retained the stock use and stock springs because they are modded stockers...maybe I'm wrong.
 
Didn't know the modded 1.9's had modded pedestals too...I thought you retained the stock use and stock springs because they are modded stockers...maybe I'm wrong.

It's what ZZP's ad says so i don't know. I don't know how "modified" they are.

https://www.zzperformance.com/grand_prix/products1.php?id=426&msg=1&catid=104

Oh, by the way, plan on after Dec. 10th doing the trans swap. Should have enough scrounged up by then. I appreciate you guys so much for helping me. It's even more a burden now because my mom's Buick Century is acting really funny in the front end. I have yet to take a look at it, but doesn't alarm me too badly, but it is my ride to school now. So me having my DD is a must, so i can take my mom to work and back and still be able to go to work, and my dad have a car also. 2 out of 3 cars being down isn't fun... lol.
 
Well...it'll HAVE to be the 12th then. Because the 19th is a XMas party and the next week...well...I'm booked for obvious reasons.

As for the pedestals...email them and tell them you want to buy just those...or ask what they do to them to make them modified...because if that's the case...you might be able to DIY that.
 
edit: nvm i re-read the entire thread, not confused anymore :).

From the pics they look like the stock pedestals.
 
Last edited:
They need to be modified for the push rod clearance. Its not much, just need to shave out enough to where they dont contact.
 


You need to modify the peds. Otherwise you'll see misfires on all cylinders as they don't open the valves properly.

If you use a caliper and measuer 10mm from the bolt opening, you'll have the correct clearnance. I've measured ZZP Peds at 10-13mm
 
You need to modify the peds. Otherwise you'll see misfires on all cylinders as they don't open the valves properly.

If you use a caliper and measuer 10mm from the bolt opening, you'll have the correct clearnance. I've measured ZZP Peds at 10-13mm

So what exactly do i do, I have never dealt with the pedestals before and quite frankly can't really picture them either.
 
I just bought a set of zzp modded 1.9 rockers second hand for real cheap. But, i just noticed they do not come with the modified pedestals. Am i completely screwed or what do i do?


Just make sure they are in fact "modded rockers" I had someone try to pass off stock rockers for modded ones.
 


Minichopper you say you can tell, can you tell by the pics of them i have, i tried to get all angles.

2i28o0p.jpg

bgvl9g.jpg

332qwr5.jpg

vhrlm8.jpg
 
on a side note. please report the difference after doing thr rockers before u do anything else. after my soon to be tune, i may get some rockers(if i get this damn job i've been holding for)
 
dude i read this stuff all day. just wanted tto know what his opinion was. i hope i can get some soon.
 


Do you not read any posts after a rocker swap? Big notice after 4K or so. End of story.

Exactly, if you want it, go for it. They greatly increase top-end, but you will not see the same effects as a cam. Rockers are said to add about 20 hp, and with supporting mods and tuning i'd say that's probably a good estimate. GP's have enough low-end that rockers are good to keep the car pulling top end wise instead of the power-band falling off, thus the dramatic hp increase.
 
Back
Top