• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by Xorbex

  1. Xorbex

    500-600 WHP Build Questions

    Looking to make 500-600WHP on PUMP gas. What size turbo and cam would be required. I have a GM 3800 Crate motor and will be putting a big cam and better flowing heads on it. Before everyone chimes in on a transmission DON'T. I am fully aware that I need a serious rebuild. This is a PROJECT car...
  2. Xorbex

    06 SE Front Air Dam and Rear Valance

    I just got into a fender bender and will need work done to the front and rear bumpers. My questions are. 1) The front air dam just clips up to the existing setup or does it replace an existing piece? 2) The rear valance.... is it the whole bumper cover or just the lower part. I guess what I...
  3. Xorbex

    comp g wheel size?

    how wide is the stock comp g rim. I've read that it's 7" but also read 6.5". ultimately I want to know the widest tire I can run on this wheel.
  4. Xorbex

    WTB: 04 Fuel pump access hatch

    I need the door for the 04 fuel pump access. My 05 doesn't have one so I want to cut it out and use the hatch.
  5. Xorbex

    42# or 60# EV6 Injectors

    Looking for a set of 42# or 60# EV6 injectors, prefferably 60#. PM me with details.
  6. Xorbex

    First time @ track s1x-3.4 - With slips

    Im 269 - I circled the wrong times Keep in mind im a complete noob to the strip and lost my virginity this weekend. My first run consisted of me spinning for an 1/8 and no i didnt just mash it. Torque brake to 2k and ease into it also trying to feather out the spin My second run I was a...
  7. Xorbex

    Water in Blower resistor and Floor board

    Any idea where water could be getting in and filling my blower resistor and blowing it. The passenger floor is also soaked. I felt around the firewall and its just a tad damp.
  8. Xorbex

    New to tuning - any tips - DHP

    Having some weird issues with DHP 1.2.4. I am unable to do any partial tunes. It usually fails on the reset and ill have to try to write again a few times for it to complete connection. When this happens most of the gauges and service lights flash through then leaving a blank cluster with only...
  9. Xorbex

    Reverse/Drive - Crack/Pop/Snap noise (not rice crispies)

    Im getting this loud snap/crack/pop noise shortly after I put the cam in. Only happens from a stop or slowing to a stop with no other symptoms other than the noise. Its a fairly loud snap when it happens. Any ideas what to check? Im gonna be pulling everything apart on Saturday for a few other...
  10. Xorbex

    Toyota pickup suprise

    Was on the highway a few nights ago after a nice country drive when at a set of lights an 80's Toyota pickup pulls up next to me. I had no intentions of goosing it cause 1) its a pickup and 2) was just out for a leisurely cruise. At the lights I see him looking over at me but never thought...
  11. Xorbex

    Why is my car so slow with the mods I have?

    Mods are in sig..... why? lol
  12. Xorbex

    What to Scan with torque

    Sorry for my ignorance but other than knock im not sure what I should be keeping an eye on with the torque app. Also does anyone know if it can read boost pressure and if so whats it called in the app.
  13. Xorbex

    Big thanks to the community

    I just want to thank everyone for putting up with my persistent questions and lack of experience working with the 3800. Ran into some roadblocks along the way and went with a different setup. I tried searching and reading about everything but the best help was from threads and live chat with...
  14. Xorbex

    Ready for Head gasket?

    Would you guys put a head gasket on that? I cleaned the SC a bit and dont really care what it looks like. The head gasket area has been scraped with a razor blade (a good one) and since ive never done this alone before is it good enough. https://copy.com/JuJm9RwNRAW4tehL
  15. Xorbex

    Modified 1.9s rockers and L32 and L26

    Thought I would share my personal experience with the modified 1.9 rockers from zzp. These will not work on some l32 and l26 heads. The pushrods will hit the heads in some cases due to the bad casting sticking out. I installed them and had major ticking and after pulling them out 9 of the 12...
See more
Back
Top