• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

valve cover gasket



Depending on which motor you have, this would change slightly.

The basics are move the few things in the way, clean surfaces, put new gasket and grommets in, then torque to 89inch lbs and put stoff back in the way.
 
1. Disconnect negative battery terminal
1a. Remove passenger side dog bone 15mm from rad support to engine bracket.
2. Unhook 7mm icm connector.
2a. Disconnect all plug wires at coil packs
3. Remove both belts
4. Remove 13/15mm nut holding ground to ICM stud (above and right of the water pump)
5. Remove ribbed idler pulley (15mm)
6. Remove SC tensioner (13mm nut in middle of tensioner pivot), and set assembly aside.
7. Loosen 15mm nut on front ICM stud
8. Remove 13mm/15mm nut holding ground wire to stud. Then 15mm to remove stud
9. Using E torx bit, loosen and remove the two studs from the head while supporting coil pack bracket.
10. Valve cover is now fully accessable. Change gasket/grommets and clean surfaces.
11. Reassemble.

Rear:
1. Remove alternator 13mm/15mm and SC to alt support bracket with Evap etc.
2. Loosen all bolts 13mm/15mmon the alternator bracket. (Key is you are going to wiggle this instead of draining coolant)
3. Remove map bracket and EGR shield 10mm
4. Wiggle alt bracket to clear the valve cover and do the gasket.
 
if i remember right you will need the two plastic elbows in the belt tensioner replaced because they will break for sure when taking the tensioner off. its the big bracket that has two small coolant hoses going into right by the alternator. you have to take that off to get to the bolts on that side of the valve cover and to be able to pull the cover off. they will have to be scraped clean and you will need a pick tool to get all the plastic out. clean up the metal where the elbows go in really well and probably use some kind of gasket sealant or something when putting those elbows back in. they are like 2 bucks at oreillys. pain. i dread those things every time i have to deal with them. if you have coolant leak after you are done, it is those two elbows. you can see one on the top. its a 90 plastic elbow, maybe 1/2 in diameter. the other is underneath and you can feel it. you can see it a little if you take the coolant box off.

p.s. don't try finding it while the car is running.
 


Pics of what? I have a billion pics of trillions of things.

Photobucket.com

ID: BillBoost37
psd: Boosted (case sensitive)


Shifting: I do way too many to be lucky.
 


First thing I'd do is call your dealer and see if its already been serviced for this, GM put out a recall on the VC gaskets and the dealer has to replace them for free if it already hasn't been done
 
asite57 said:
First thing I'd do is call your dealer and see if its already been serviced for this, GM put out a recall on the VC gaskets and the dealer has to replace them for free if it already hasn't been done
Click to expand...
Not gasket"s", the recall is for the front VC gasket only, on the supercharged engines.
 


The essentials of what they do is maybe a front VC with or without grommets. Remove the heat shield from the exhaust, remove the wire holder (above the damn gasket..lol) and put clips on the wire.

Personally, I'd replace the gasket myself. Remove the heat shield and be done.

Kawa.. you want pictures of it.. go search my photobucket,
 
You must log in or register to reply here.
Back
Top