• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

pulley help anyone close to york pa

J

jspangler22

New member
was wondering if there was anyone who loved close to york pa. That could help me with a pulley swap. And what tool i need. Or does anyone know how much a garage costs to do this
 


Near as I can tell, if you can't operate a pulley puller, you're probably best off not modifying the car yourself. I assume a puller will some with instructions,too.
 
Oh, and since you didn't mention anything, I would suggest doing some research and doing intake/exhaust flow mods before changing to a smaller supercharger pulley. Without them, it's likely you will blow up the engine. That is to say, if you haven't done such mods already.
 


I didn't care where it was..lol

Just saying.. if you look at a map, PA is right below Drunkie..Just to the left of me.. and on long freaking state to drive through.
 
ive been there before, but i clearly am unsure cause its right in the middle of the two 'zones' as i see it.
 


Zones.. ??? two zones of good road, seperated by the hell of 40 mile construction and the worlds largest recorded pothole which you are sidetracked from seeing by the Billboard sized sign stating there is a drunk driving checkpoint 2 miles down the road (please exit now).
 
yea its ne. And yea i already am working on all other mods before i drop the pulley in the main expense is the aeroforce gauge 240 bucks
 
i have a puller i am rite in n.e philly i can meet half way and do it its not hard i could bring toold i usely get like 50 bucks and sum gas money if intrested
pm me if so..
 
just found this and tad late in response. im located in lancaster, about 30-40min north of york.

edit-i think i still have a pulley puller in the garage somewhere. bur like others said, if u havent modded/tune the car to support the pulley, do it now before dropping sizes
 
fst said:
just found this and tad late in response. im located in lancaster, about 30-40min north of york.

edit-i think i still have a pulley puller in the garage somewhere. bur like others said, if u havent modded/tune the car to support the pulley, do it now before dropping sizes
Click to expand...

I am going through Lancaster the weekend of Sept 9-11. Would you be able to meet me at the outlets to swap my stock pulley and ZZP MPS?
 


97PAGTP said:
I am going through Lancaster the weekend of Sept 9-11. Would you be able to meet me at the outlets to swap my stock pulley and ZZP MPS?
Click to expand...

honestly it'll take prolly like an hour give or take depending on how much a ***** the stock pulley is and pressing on the MPS. i havent done one in a few years since gone to turbo:o. maybe either you or i should read up on installing the mps. pulling the stock one out is simpler IMO :th_laugh-lol3:
edit-if the outlets you mean rockvale, i live like 15min away from there. could just come to my place and trackle it there.
 
The colder the blower is the better.

I drove 15 minutes grandama style, let it sit for another 20-30 and i still ended up with a bent stock pulley.
 
matt5112 said:
The colder the blower is the better.

I drove 15 minutes grandama style, let it sit for another 20-30 and i still ended up with a bent stock pulley.
Click to expand...

Crap, mine would be hot since I'll be driving 2.5 hours before getting to Lancaster.

Fst - Anyway I could borrow/rent it, then ship it back to ya?
 
You must log in or register to reply here.
Back
Top