jlgp2007nc
New member
Comes with the territory. I'll be more careful next time.
JLGP's Eva 07 GP Base
- Thread starter jlgp2007nc
- Start date
jlgp2007nc
New member
Selling what's left of the trans for $250 OBO. I can't use it.
Doug 97 gtp
New member
looks a little cleaner, you should definetly replace the crank seal it is 10000000X easier when the motor is out
jlgp2007nc
New member
Ha yup! Took the front cover off and cleaned the heck out of it. Replaced every gasket except that back cover and rear main. They weren't showing signs of leaking and seemed OK so I left them alone.
jlgp2007nc
New member
More pictures of the destruction....
The broken skirt on the opposite side of the chip.
See all of the scoring on the cylinder walls on the left compared to the smooth on the right?
The rod journal looks to be intact. The rod bearings didn't spin.
The broken skirt on the opposite side of the chip.
See all of the scoring on the cylinder walls on the left compared to the smooth on the right?
The rod journal looks to be intact. The rod bearings didn't spin.
jlgp2007nc
New member
That.....was a b**ch.
I will be pulling an all nighter some time this week.
jlgp2007nc
New member
See LIM bolts down both ways.
Sent from my SPH-L720 using Tapatalk 4 Beta
Sent from my SPH-L720 using Tapatalk 4 Beta
jlgp2007nc
New member
jlgp2007nc
New member
I just want this ufcking nightmare to be over. I've seriously had it. It has been to ufcking long ufcking months. I finally hit the weekend where I could be driving this god damned car TONIGHT. if only my front exhaust header didnt bump against my head studs. Seriously? The rear went right on so what the ****ing ufck! They're even the same heads from my top swap. Ugh....
End ufcking rant
Sent from my SPH-L720 using Tapatalk 4 Beta
End ufcking rant
Sent from my SPH-L720 using Tapatalk 4 Beta
jlgp2007nc
New member
jlgp2007nc
New member
jlgp2007nc
New member
Well I drove around maybe 30mins.
There's a stumbling like with my last setup in right at the transition into boost. Can hear popping from the exhaust, hesitation...but 0kr on the scan.
Almost seems like it happens more on a gear change. Maybe torque management pulling something and the engine doesn't like it.
That's what destroyed the last engine so I'll be hunting this ghost down.
Sent from my SPH-L720 using Tapatalk 4 Beta
There's a stumbling like with my last setup in right at the transition into boost. Can hear popping from the exhaust, hesitation...but 0kr on the scan.
Almost seems like it happens more on a gear change. Maybe torque management pulling something and the engine doesn't like it.
That's what destroyed the last engine so I'll be hunting this ghost down.
Sent from my SPH-L720 using Tapatalk 4 Beta
jlgp2007nc
New member
https://www.youtube.com/watch?v=KlbXGO__-dM&feature=youtube_gdata_player
Sent from my SPH-L720 using Tapatalk 4 Beta
Sent from my SPH-L720 using Tapatalk 4 Beta
Fivefingerdeathpunch
New member
Perhaps fuel related or misfires because of the popping sound.
What PCM and tuning software are you using?
What PCM and tuning software are you using?
jlgp2007nc
New member
I'm still using hp tuners.
Sent from my SPH-L720 using Tapatalk 4 Beta
Sent from my SPH-L720 using Tapatalk 4 Beta
jlgp2007nc
New member
I'm never using a MAP sensor again.
Sent from my SPH-L720 using Tapatalk 4 Beta
Sent from my SPH-L720 using Tapatalk 4 Beta
jlgp2007nc
New member
Apparent oil starvation issue from the L26. This is from #6 rod journal I believe. I loosened all of the rod caps and rotated thr crank around pulling pistons and found this bearing spun half way around but the tangs aren't shaved off.
Either way...no budget for machining. Closer and closer to giving up on her.
Sent from my SPH-L720 using Tapatalk 4
jlgp2007nc
New member
De-Mod
Sent from my SPH-L720 using Tapatalk 4
Sent from my SPH-L720 using Tapatalk 4
jlgp2007nc
New member
Yeah it happens. Back to basics and come back with an RWD V8.
Sent from my SPH-L720 using Tapatalk 4
Sent from my SPH-L720 using Tapatalk 4