• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

GT 0-60 times?

S

skeelo58

New member
Does anyone know what the 0-60 time is supposed to be for a 97-03 GT? My 02 is stock, and I timed it tonight and it averaged to about 9.4 seconds. Does that sound about right?
 


That does seem a little slow. Mine's usually about 9, but your 02 has the 3.29 gearing and my 04 has 3.05 and needs some TLC lol.
 
Wonder why it would be so slow? I was planning on Seafoaming it sometime soon, think that would make a difference at all?
 


I ran 7.9s- 8.3s stock. So yea you are about a sec off from average. BTW i finally cracked the 6 sec range 0-60 yest at a swift 6.8 sec lol.yay :th_peaceout:
 
Hippo Machine said:
Here is my 35-80 i believe, stock gt. Not really relevant, but ya...

video-2011-10-07-19-02-50.mp4 video by joebom123 - Photobucket
Click to expand...

Ummm, must be the wrong video because you went no where in that one LOL

Here is my GT...It has a custom tune (33* WOT timing), Open Cone Intake, 180*, AL606's gapped at .050", solid lower mounts, poly upper squares/bushings, and a homemade HV3 with a P&P'd Lower Intake Manifold...oh yeah...still has the stock cat/u-bend/dp...lulz.

Easy Roll Out in the Silver Kar to 65 video by bluegtp03 - Photobucket

35 Kick in the Silver Kar video by bluegtp03 - Photobucket

60 Roll in the Silver Kar video by bluegtp03 - Photobucket

Yeah...slowsauce...furealzbreh.
 


How did you launch it? If you just floored the gas that probably cost a few tenths. If you brake torqued you might pick up a few. Also how did you time it? Maybe your timing method is skewed.
 
stealthee said:
How did you launch it? If you just floored the gas that probably cost a few tenths. If you brake torqued you might pick up a few. Also how did you time it? Maybe your timing method is skewed.
Click to expand...

Perhaps...




































































Egg-Timer.jpg


?
 
stealthee said:
How did you launch it? If you just floored the gas that probably cost a few tenths. If you brake torqued you might pick up a few. Also how did you time it? Maybe your timing method is skewed.
Click to expand...

I had a stopwatch to use as a timer, so I don't think my method is what's wrong... I did just floor it. From what others are saying I'm roughly 1.5 seconds slow either way? It was a fairly cool night, and the car was warm when I tried it out. I'm just gonna hope a clean air filter and seafoam treatment help out a bit
 
Get rid of that factory U-Bend too...and run a higher octane...it's probably knocking like most factory 3800's and pulling timing above 4k~
 


here is my 0-60 vid. u-bend/res delete, 08 imp SS catback and fenderwall intake.
1/4 throttle brake launch till it stops spinning and floored it, if you turn ur speakers up you can here the tire trying to break loose again i think lol. once i get to 80-85km/h i hit a hill and it really slows down lol.
 
I agree with you both, 2nd gear is crap. and yes blue even going downhill once you hit second gear that speedo needle slows down lols, but i was starting to hit a hill thats no lie. thats why the video abruplty stops cause im not going to go WOT to the top of a hill cause 1 its dangerouse and 2 the speedo needle would of stopped most likely lols.
 
You must log in or register to reply here.
Back
Top