• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Driving with loose tie rod nuts?

natethegreat

natethegreat

New member
Had to do some work on the front end and in the process thought it'd be easier to remove the tie rods from the knuckle. Well about halfway down the threaded part the tie rod just started to spin. Did this on both sides. Well, i've tried everything and can't get them to either come off, or get tightened up. I need to drive the car tomorrow, on the highway. I plan to get new tie rod ends and just cut the old nut off to change em out, or something like that.

On a side note, I tried to change out the front sway bar with a dorman bar i pulled off a prix in the scrap yard. Its thicker that the stock one, and can't seem to get it to fit. Would Speed Daddy Headers get in the way of the sway bar? It kept hitting the downpipe, while the stock one slid right in. Any thoughts?
 


I wouldnt drive it.

Does the stud on the tie rod have allen key to help hold it?

Or use a pry bar to push the tie rod end down, force the cone shape to wedge itself into the knuckle. Air tools/electric impacts help alot.
 
If it did, it doesn't anymore. I tried the breaker bar trick and that didn't work. I put a c clamp on it to push it into the knuckle and that didn't work. Tried our impact and that didn't work, But its a tiny compressor with a ****ty air ratchet on it.
 
heat the piss out of the nut, spray it with some lube, try some more.

or a nut cracker can be used, or a sawsall, grinder what ever you got to work with.
 


mars5l said:
are you using an air ratchet or an impact gun?
Click to expand...

Pretty sure he's using an air ratchet- " its a tiny compressor with a ****ty air ratchet on it"

Might also try some PB Blaster on it and then use a wire brush to clean out the exposed threads before backing it off.

Usually if I can't get a tie-rod to set I just smack the top side of it closest to the knuckle with my 2lb hammer a few times and it sets enough to tighten back up, and that's using a standard ratchet. If I break out the impact then it zips it on/off with no issues as long as the threads are clean.
 
FordMan77 said:
Pretty sure he's using an air ratchet- " its a tiny compressor with a ****ty air ratchet on it"

Might also try some PB Blaster on it and then use a wire brush to clean out the exposed threads before backing it off.

Usually if I can't get a tie-rod to set I just smack the top side of it closest to the knuckle with my 2lb hammer a few times and it sets enough to tighten back up, and that's using a standard ratchet. If I break out the impact then it zips it on/off with no issues as long as the threads are clean.
Click to expand...

But he also said impact just before that in that exact same post..
Tried our impact and that didn't work
Click to expand...
so that's why I bet mars was asking for clarification.
 
the ONLY easy way to remove/change oem tie rod ends is to first use a cutoff wheel and cut off the nylock top of the nut and the stud to remove the rusty threads/nyloc portion that end up trapping the rust dust and permanently wedging them together.

once you remove the stud and the nylock portion of the nut you can take em off with a ratchet or an impact in 2 seconds.

if youve been spinning the rod ends inside the aluminum knuckles for long enough your new rod ends may wallow em out and require new spindles.

a nut splitter works quite well too but ive been using the cutoff and zip method for a long time now since they got rid of cotter pin secured oem parts for this new nylock stuff that ****s you after a couple years of rust
 


Thanks guys. Ended up just using grinder and cutoff the stud. It didnt really ream the spindle per say, i think they were too loose the whole time.

The swaybar is 34mm, and seems to have a bend thats not in the stock one. Perhaps ill just mess with it some more.
 


If they are OE tie rods, they are nylon locknuts. You'll get them off real easy by applying heat. To pop them out of the knuckle, use a BFH or deadblow and hit the tapered part with the threads upward. Apply more heat if it becomes a hassle.
 
stealthee said:
But he also said impact just before that in that exact same post.. so that's why I bet mars was asking for clarification.
Click to expand...
Yes, just wanted clarification. Air ratchet doesnt spin fast or hard enough compared to an impactgun, but he got the tie rod off.
 
You must log in or register to reply here.
Back
Top