• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Delilah....dyno rackar



Re: Her names Delilah...lots of Tender Love & Care coming

No I could allow DoD to work with this if I really wanted. But it's thinner than the ls4 one and has better oil passages. Plus I relocated my OPSU to oil filter instead of on top. So when I finish the oil passage an aluminium plate and rig weld it

Sent from my HTC6525LVW using Tapatalk
 
Re: Her names Delilah...lots of Tender Love & Care coming

You'll want to dig farther down in the passage, make the "floor" lower
 
Re: Her names Delilah...lots of Tender Love & Care coming

I was going to. I only had two dremel bits and the tray destroyed them. I'm gonna go get some metal dremel bits tomorrow. All though, cutting the rivets off is the easiest part

Sent from my HTC6525LVW using Tapatalk
 
Re: Her names Delilah...lots of Tender Love & Care coming

I forgot I used a regular drill bit to get the majority of the material out and then used a dremel to smooth out
 
Re: Her names Delilah...lots of Tender Love & Care coming

I started with drill but. But I well

Sent from my HTC6525LVW using Tapatalk
 


Re: Her names Delilah...lots of Tender Love & Care coming

Tomorrow morning I just gotta finish the oil passage and knock the rest of the rivets out


And damaged the gasket....fu*k my life. Can't get a replacement gasket either


Sent from my HTC6525LVW using Tapatalk
 
Re: Her names Delilah...lots of Tender Love & Care coming

Well since zzp won't replace their shifty ball joint I'm going to go pick up some moot ones....not even had them a year and my passenger ball joint is shot

Sent from my HTC6525LVW using Tapatalk
 
Re: Her names Delilah...lots of Tender Love & Care coming

And bam. Done.


Now off to the shop for some good ole tig welding

Sent from my HTC6525LVW using Tapatalk
 
Re: Her names Delilah...lots of Tender Love & Care coming

So I got a couple question....would moving my coolant over flow tank and windshield washer tank (different square tank and different pump...but easy swap) to the trunk work fine as long as there's no leaks. I see no problem doing

Sent from my HTC6525LVW using Tapatalk
 
Re: Her names Delilah...lots of Tender Love & Care coming

i would not run the coolant tank that far, but the washer tank can be relocated for sure.

not sure if it will fit your year car, but the 97-98 cars have coolant tank thats tucked away in the corner by the factory air box.
 


Re: Her names Delilah...lots of Tender Love & Care coming

Well I found a nice coolant tank for 50 bucks that is square and comes with a pump that can be replaced.

As for the coolant tank I don't see any problems it could cause. Cause when engine warms up it can still overflow into it then when it cools down it can still pull coolant back in

Sent from my HTC6525LVW using Tapatalk
 
Re: Her names Delilah...lots of Tender Love & Care coming

But what happens if it starts a leaking coolant all in your trunk and interior?
 
Re: Her names Delilah...lots of Tender Love & Care coming

The coolant lines wouldn't be in the car except for about a foot in the trunk. Obviously once I install it I'd check it often to make sure no leaks....then it should be fine.

Sent from my HTC6525LVW using Tapatalk
 
Re: Her names Delilah...lots of Tender Love & Care coming

I used a cheapo $10 universal plastic tank from AutoZone...just mounted it up against the front next to the diagonal brace, which would be directly in front of where the stock airbox would have been. I ran the hose above the rad fans in the factory harness as well, all tucked away clean. Worked good for me.

enginebaydec11.jpg


Edit* Don't mind hose placement; I was just testing it out.
 


Re: Her names Delilah...lots of Tender Love & Care coming

you got all that room now where your battery used to be, move your new coant tank there.


WtktKGN.jpg
 
Re: Her names Delilah...lots of Tender Love & Care coming

It doesn't fit well. My catch cans are going there and I'm gonna see if I can find a way to fit coolant there

Sent from my HTC6525LVW using Tapatalk
 
Re: Her names Delilah...lots of Tender Love & Care coming

DirtDog said:
It doesn't fit well. My catch cans are going there and I'm gonna see if I can find a way to fit coolant there

Sent from my HTC6525LVW using Tapatalk
Click to expand...
There's plenty of room after that gay gm overflow tank get tossed for catch cans in that area I managed to fit nitrous solenoids, and two catch cans there and still able to pull my intake out with out hitting anything. Regardless it'll work either side just try to keep your lines short and direct as possible
 
Re: Her names Delilah...lots of Tender Love & Care coming

Rgr I'm gonna mount the catch cans today and go pick up some supplies from oreillys for hooking them up

Sent from my HTC6525LVW using Tapatalk
 
You must log in or register to reply here.
Back
Top