• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

bought some company for roofie

What do you think?

  • Total voters
    21
  • Poll closed .
Re: My project car

Might be able to help you a little bit tomorrow after I get my lowering springs on. I'm in Cove till Monday, but the rear struts take me forever to get out because of my bad back lol.
 


Re: My project car

far right, is the t-stat gasket, I think (hard to tell from pictures) look at area 2, in my picture i made for you, thats where it goes.

the 2 orange go on the top side of the lower intake, (and they probably came with the supercharger gasket also) (probably in yellow) the intake will have a little lip where you can put them. look at area 1 of my picture they are the two little yellow circles

the only other thing i can think of is the heater bracket on your 98 (and 97 cars) might have some rubber o-rings where the 99+ cars have a plastic elbow. your bottom one is metal, and a better design if you ask me. refer to area 3, (the alt bracket)

S6300015-1.jpg
 
Re: My project car

Thanks that diagram will help.... Mike bad ass bro, I wanna so your gtp in person once your done putting on the lowering springs on
 
Re: My project car

those two orange ones are way too big for the lim coolant passages between the blower and the lim.

They are the correct size for the coolant elbows.

The blue plug looking piece is the seal for the L36 MAP sensor.

The largest black o ring most probably fits on the rear vac fitting on the L36 UIMs.

The smaller black o ring fits on the PCV or the L67 vac tree.

If they don't slide in easily, put some grease on the bore that you're trying to slide them in.


Is it REALLY that difficult to look at the places where you have o rings and just see if any fit there?
 
Last edited:
Re: My project car

It's not hard, lol I looked all over last night and sizes were just wrong for anything I could find last night add alcohol and game over lol also my garage looks like a war zone now and I don't feel like cleaning it.
 
Re: My project car

Anerobic sealer is what you want for the snout.

Nothing else.

Because the oil eats through the RTV.

Every.

Time.

Otherwise, this could be the worst drunk purchase of your life, congrats LOL.
 


Re: My project car

not trying to hijack but if the rotor plate comes away from housing do u seal it too? sorry if wetawded lol
 
Re: My project car

A couple of quick questions lol I almost have this car reassembled hurray me, but having a few issues for starters there is a t-pipe that goes on the fuel rail one side goes under the sc cone to the rear or the engine the other side goes where?
C90AB330-C059-439B-ABB0-436A4CA30F49-3217-0000029B423D51E8_zps1c982dfc.jpg

I don't see any it could go that it can reach. Also there is a wire connector that comes out of the tubes that house the wires for the fuel injectors where is the other side of it lol
6091DB31-68DF-48C1-BC36-CD03A02F8029-3217-0000029B3E2FCCD0_zps87c35c46.jpg

and hopefully lastly (don't know what any of these things are called but here we go anyways)
E0A15A30-49C5-4DB7-B0D4-AD5F77B270EB-3217-0000029B369EE5B4_zps15640b73.jpg

okay just like the bolt that holds on the engine cover but is it suppost to be a super tight fit? I can't seem to get it back on properly, any ideas?
 
Re: My project car

I forgot 97-98 blowers had the stupid vac tree.
But here is the vac diagram for the car hope it helps. I don't know what that plug is for.
2011-07-04_145638_vacuum.jpg


Idk if this helps any but here is a pic of my harness and that is plugged into something going to the front of the engine.
scaled.php
 
Last edited:


Re: My project car

He got it running after I went over so he could look at my car to see where things go haha, although it is making a hissing noise. He took it for a test drive with me following just in case, it ran good. No DTC's, I put a scan tool on it. It has full boost as per the factory gauge. Makes me want to knock the LIM out on my car, but instead I installed lowering springs. Also hooked him up with a newer right corner housing.
 


Re: My project car

And don't worry Mike we will knock yours out as soon as we can. Also want to say thanks to everyone who posted diagrams and gave helpful advice. This is the most intensive repair I have attempted my self
 
Re: My project car

You did good bro for never having owned this platform before. You saw how I did the springs so it should be easy for you after doing the LIM.

Here is Shane's motor complete right before firing it up.
shanesgtp1.jpg


Also a common site, hoods up on GTP's Lulz...
shanesgtp2.jpg
 
Re: My project car

I just wanted post 100 to be of good things.... Car is running strong, I am happy and drunk will paint do some more maintince to include a proper waxing lmao and put some better sized tires on it but taking a day off or 2 will update when it's time to dive back in, prolly soon loving this car again.... Also I can not say it enough thank you everyone for your help
 
You must log in or register to reply here.
Back
Top