• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by outonthetiles

  1. outonthetiles

    Turbo L36 Volvo 240

    I figure its about time to start a build thread on this car. It's a '90 240 DL sedan. Originally the car was a 2.3 I4 5 speed that I turbo'd. I was running ~14lbs of boost through it and making probably in the neighborhood of 200whp. The engine and trans had high mileage, and I was at about...
  2. outonthetiles

    WTB: PRJ or ZZP fuel logs

    Looking to buy some fuel logs for my full stack intercooled build. I know its a long shot, but is anyone looking to sell?
  3. outonthetiles

    XP Cam Intake Centerline

    Does anyone know the intake centerline of an XP cam? I am having a hard time finding this info.
  4. outonthetiles

    anyone make roll center correction ball joints for the 99-03 cars?

    That is an option, but I'd rather not have to fab new ball joints when they wear out. I'm thinking about having something like this machined:
  5. outonthetiles

    anyone make roll center correction ball joints for the 99-03 cars?

    I have been thinking about this for a long time as I want to lower my car but I also autocross it. I haven't looked if it was possible but I want to cut off the factory mounting points for the LCA and weld in mounts for these control arms a couple inches higher on the subframe. The other...
  6. outonthetiles

    '00 Impala LS - 5 Speed and Supercharged

    I've been a member here for a few years so I figure its about time to introduce my car. It's a 2000 Impala LS, which I did a Getrag 284 5 speed swap, LSD, a GenV top swap, XP cam, C5 brakes, HUD, among many other things. Its not a GP, but I think you will be able to appreciate it. This won't...
  7. outonthetiles

    WTB: 3.5 pulley for ZZP hub

    Looking for a 3.5" pulley to fit a ZZP MPS hub. Can pay with PayPal or could trade you for my brand new never used 3.4.
  8. outonthetiles

    Anyone have any problems with Felpro front main seals?

    Just finished a cam install on my Impala yesterday, and now I have a pretty good oil leak coming from the front timing cover area. While I had the timing cover off, I replaced the front main seal with a Felpro one that came with the timing cover gasket. I pulled the balancer back off to reveal...
  9. outonthetiles

    wtb: xp cam

    Looking for a low mile XP cam.
  10. outonthetiles

    wtb: 42.5lb injectors

    As the title say, looking for some low mile injectors. Let me know what you have.
  11. outonthetiles

    Pic Request

    I'm going to retrofit a GP HUD into my '00 Impala. Does anyone have any pictures of how the HUD unit mounts in the dash? Thanks.
  12. outonthetiles

    WTB: L67 Fuel Rails

    Looking to buy some stock gtp fuel rails in good shape. Thanks. EDIT: Found. I'm all set.
  13. outonthetiles

    WTB: XP Cam, 105lb springs, ls retainers

    Looking for an XP Cam in excellent shape. I also need low mile 105lb springs and ls retainers. If you have any of these for sale, PM me or e-mail me at [email protected] Thanks.
  14. outonthetiles

    Keyless Front Door Handles

    I saw a write up on one of the GP boards a while back about using rear door handles on the front, as they were keyless. Some modification had to be done, as the arm that pulls the rod for the latch mechanism needed to be moved from the from the front to the back. I think I may have found an...
  15. outonthetiles

    Aluminum Oil Pan Gasket?

    I'm swapping to an aluminum oil pan from an 05 GP soon. On rockauto, I don't see a gasket listed for the oil pan. I know that in the previous years, the windage tray was built into the gasket, but in the aluminum oil pan the windage tray is built into the pan. Can anyone point me to a part...
See more
Back
Top