• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by oneil.GTP

  1. oneil.GTP

    fps russia

    might know about him, but for the ones on the outside.. website youtube and who cares if he's really from GA, dont be beech and half nice day.
  2. oneil.GTP

    whats your speed

    not sure if there's another thread on here, but the AT&T rant thread got me curious, so here. what's your speed? i use Speedtest.net - The Global Broadband Speed Test and find it fairly accurate.
  3. oneil.GTP

    1 in 6 americans..

    saw this earlier today..had to share it lol. america trying to feed the already fat yet again.
  4. oneil.GTP

    Anderson Motorsports, IL

    anyone been there before? planning on going down there in a few weeks for a tune was curious if anyone had thoughts on this place? Chassis Dyno Tuning Anderson Motorsport Clinton IL
  5. oneil.GTP

    Rear hub/wheel bearing..

    what's the difference between the rear hubs on rock auto and zzp.com? rock auto's is 283 and zzp's is 89? confused..
  6. oneil.GTP

    tire sizing (wider)

    so i read the sticky, didnt help much. ive always just gotten the stock size for replacement, but im thinking of going a bit wider. all on the stock 16's. so stock is 225/60/16 is 245/55/16 the same thing, just a bit wider? i cant for the life of me figure out what all the dimensions and what...
  7. oneil.GTP

    ses light cycle time?

    just put in a new upstream 02 sensor and the harness. it threw the p0420 code after my header install, and i also just put on an o2 emulator. so why's it still saying p0420? is there a cycle time for reset, or should it already identify the o2 sensor and emulator and eliminate the ses light...
  8. oneil.GTP

    engine/trans mount or suspension squeek?

    theres been a consistent "squeek" when going over even the slightest of bumps. decided to take a look yesterday and as i was jacking the car up there was a popping/squeeking noise coming from near the front cradle. i couldnt locate where its exactly coming from but my only two thoughts are...
  9. oneil.GTP

    3.4 or 3.5

    i have ssacs, 4" open cone, zzp tune and few other bolt ons. i dont have my own scanner but could borrow one from a buddy if needed. i wont be going further than a 3.4, its not in my intrest. main question is how big of a difference between the 3.4 and 3.5 besides the obvious? i dont race, jus...
  10. oneil.GTP

    ssac hardware?

    ordered them, but curious whats all included if anything? i read i need clamps, what sizes? i got copper rtv and new header bolts. anything else?
  11. oneil.GTP

    LOL

    YouTube - hillbilly car jump!! oh too funny lolol.
  12. oneil.GTP

    flash floods

    with all the rain we got here in illinois over the past week, decided to take some pictures and videos of the damage. this is on the spoon river located on the county line of peoria and stark county. every road was submerged atleast 2-3 feet. the river from the bridge. waters normally 15 feet...
  13. oneil.GTP

    which harness for bose

    so i got a cheap aftermarket headunit. the stock one took a poop. it came with free shipping, the wire harness and installation bullsh*t. so more power to me, nothing wrong with free. anyways im planning on doing the 70-1858 harness, because its cheap. i read thru this...
  14. oneil.GTP

    seafoaming question

    after countless hours of reading, i'm just going to ask. this is the how-to i'm going off of, and was wondering if it's accurate; Grand Prixs Of North America • View topic - Seafoam writeup now i know what i need, and where everything goes, for the most part. my main concern is what vacuum...
  15. oneil.GTP

    e20 or bust

    been getting the e20 code lately on the stock stereo, went ahead opened it up, cleaned the lens, only to find out now the damn motor wont stop spinning. thinking there could be a sensor i need to reset? but anyways.. regardless if i get the pos to work again, i'll be looking into some...
See more
Back
Top