• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by abuckley1290

  1. abuckley1290

    In a world of S**** with new deck please help

    So i got a second hand alpine cva-1004 for cheap. I got everything wired up perfectly then decided to add the bypass module to watch movies when I am driving. Upon doing this i forgot to insulate a +12v wire and POP everything shuts off when i went to put it back into the dash (it grounded...
  2. abuckley1290

    Need Help with fuel pump removal

    I cannot locate the snap ring on my fuel pump. I can only find directions for cars older than 2000, so i am guessing maybe my 2002 is different?
  3. abuckley1290

    Rim Opinion

    I have two sets of Rims I am looking at. Need help if they will fit or not First Set. Tire Size= 275/45r/20 Second Set= Tire Size 245/35r/20
  4. abuckley1290

    Cool Trick with HIDs..

    I put my HID's in today and noticed a trick. I am not sure if anyone has noticed this but I figured id share it. In my 2002, if I leave the high beams on the headlights turn off. This also means that the security flash has no headlight, just corners. So I did not have to do a rewire and i...
  5. abuckley1290

    Any one do this? DIY o2 emulator?

    I was looking around and found this. I plan on removing my cat/u bend and replacing it with a glasspack and placing the o2 bung with this DIY emulator. Think it would work? Here is the link... http://forums.bimmerforums.com/forum/showthread.php?t=525568
  6. abuckley1290

    Considering a Dodge Charger...

    Got a few questions on this one. My grand prix has hit about 125k and I have been wanting to get something newer for a while. I love the car to death but I always like to get new things. I have been looking at a 2008 Dodge Charger (base model with the 2.7l v6). Does anyone have any...
  7. abuckley1290

    Subwoofer wiring help needed bad

    Heres the story. I traded my old setup for 2 kicker 12" L7s. I get up their everything looks good so i take it. Upon removing my old subwoofer the ground wire for my amp got messed up so, being in a hurry, I did not test them and brought them home. When i took them out of their speaker box i...
  8. abuckley1290

    ported rear deck

    hey guys im planning on redoing my system. I have been interested in a while in porting the rear deck to get some of the bass thats trapped in the trunk up to the front of the car. My question is i have seen to basic designs. The first being just putting holes by the rear speakers so the bass...
  9. abuckley1290

    DHP Pcm

    This is kind of a stupid question but where can i get a Digital Horsepower PCM for a 2002 GT? Their website says 3800performance carries them but ive heard they are ZZP pcms and PYFC.com only has them for the grand am...so where can i get one?
  10. abuckley1290

    Hit pothole..now ABS and TRAC OFF lights stay on

    So just as the title says i hit a pothole and now these two lights are on. They usually come on right when i go into drive if not a few moments later. What could the problem be....? thanks
  11. abuckley1290

    RPM Issue

    Okay i've had this issue since i purchased the car but here is what happens. When im cruising along at pretty much any speed and let off the gas all the way the rpms either stay were they are or slightly raise for a second or so then finally go down to 1000 rpms or so where they should be...I...
  12. abuckley1290

    Strange noise from front wheel

    Today my car started making a grinding noise coming from the front left wheel. It sounds similar to worn break pads (metal on metal grinding) and only happens when the wheel is turned pretty far to the right (high and low speeds). Any ideas what it could be? Its not a steady noise but it...
  13. abuckley1290

    Pulley making metal grinding noise??

    This has been going on for a while now and it got profoundly louder today. It sounds like metal on metal grinding. I looked down and the noise is clearly coming from the A/C compressor pulley. Do i need a whole new compressor? or can i just replace the pulley assembly? Thankyou
  14. abuckley1290

    Alternator voltage boost

    I want to run the 1 amp diode parallel to the orange wire. i went to radio shack looking for this diode and they have all different voltage 1 amp diodes? The guy told me to find out what voltage then come back so my question which one do i need?
  15. abuckley1290

    Volatge Boost Mod question

    I want to run the 1 amp diode parallel to the orange wire. i went to radio shack looking for this diode and they have all different voltage 1 amp diodes? The guy told me to find out what voltage then come back so my question which one do i need?
See more
Back
Top