• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

What did you do to your Car today?

Status
Not open for further replies.
blew my exhaust pipe off, down pipe and res dropped and dragged for 2 blocks till i could find a clear spot to park and put it back together.

looking into a band clamp for it now, normal clamps keep failing me.
 


Was gonna wash it but then..
vuqadyqu.jpg


Sent from my HTC Thunderbolt using Tapatalk
 
Found me a l67 motor with 92k miles 400 dollars pulling it out and taking it home to swap out my 189k mile l67 couldn't pass up the deal.. just hope it fits BC it out of a Buick park avenue ultra

Taz238
 
My full set of GR-2s arrived today (rock auto got them here in two days). Waiting on strut mounts and 3 inch DP from ZZP...which shipped today.
 


Did a few pulls today and felt like a honda spinning though gears... so a few moments ago i broke down and bought some new DR's and new rear tires since i was peeling money out of my wallet.
 


Got a new ign. module because of skipping only find it runs worse & dies. Took it to Chevy mech. and they flashed modules, cleaned the MAF sensor & throttle body.

Picked it up and still skips at part throttle so gotta pedal it like a dragster. Eng. light is back on.

It's had a trans. shop check for issues. My mech. put a new fuel filter on & the ign. module. Fuel pressure is ok. Has 170k miles on it.

Plugs were done about 100k miles. Getting new wires on Monday & thinking of plugs too while they're at it.

I usually do this **** but my back went out with the XMas paper and it's winter so we're screwed.

Is it a sensor or what's the problem?.!

-- Sent with :banghead:
 
go to a autozone parts store, they will scan it for free.

or buy a cheap scanner, i got one shipped for 16 bucks. i got sick of waiting on line for the free scan.

or if you have a droid phone you can get the torque app for your phone $5 for the app, $15 for the obd2 blue tooth.
 
Scottydoggs said:
go to a autozone parts store, they will scan it for free.

or buy a cheap scanner, i got one shipped for 16 bucks. i got sick of waiting on line for the free scan.

or if you have a droid phone you can get the torque app for your phone $5 for the app, $15 for the obd2 blue tooth.
Click to expand...

Yep second the suggestion for the Bluetooth dongle and torque app... it's helped me diagnose plenty of cars...

Sent from my Galaxy Note 3
 
We have a Craftsman 9 87702 CanOBD2 code reader. Guess I gotta get outside and see. It's an assload of snow outside.

-- Sent with :-)
 


Scottydoggs said:
the code holds the answer 99% of the time.
Click to expand...

The funny thing is there were no codes until after a replacement ign. ctrl. module was put in and it died all over town. Then Mr. Goodwrench flashed some **** and it still sputters but it doesn't die at least. We've been digging out and the plow guy is out there now.

THANKS!

-- Sent with :-)
 
My power steering was starting to make just a little bit of a whining sound on the way home, I bet the reservoir is going low again, I'm gonna go out and check it and top it off with lucas again.

Also stealthee your shed is identical to mine. Ours is a bit custom with gutters and electricity but it's the same lol.
 
Status
Not open for further replies.
Back
Top