• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Search results

  1. JoshMcMadMac

    FS: HPTuners

    I have an "original" (not the new MPVI 2) standard HPTuners for sale. It is unlocked for the 2000 Pontiac Grand Prix as well as the 2009 Saturn Sky. It does not have any remaining credits since it is opened to both models, not VIN-specific. $400 shipped CONUS, and I will work to accommodate...
  2. JoshMcMadMac

    It's Been Fun

    Although not always the best place for help, this site has been a lot of fun since its inception. I sold the GTP a month ago, and tried to bring myself to buy another one...but it just was not in the cards. I got a nicer car out of the deal, and back into a RWD V8 platform. I just wanted to...
  3. JoshMcMadMac

    Crank, but no start

    2000 GTP, stopped working randomly today. I replaced the crank and cam position sensors a few months ago. The fuel pump resistor is bypassed. Plenty of fuel in the tank. Well maintained in general. I commute about 35 miles to work, about 45 minutes. Half way to work, 25 minutes or so, the...
  4. JoshMcMadMac

    Fuel Pump? Coil Pack?

    The car died on me today. Friday I drove home from work, which is about 30 miles. I pulled up to check my mailbox, and the car stalled out. I tried to start it back up, but all it would do is turn over. I proceeded to push it forward so I could roll it back into the garage. I jumped into...
  5. JoshMcMadMac

    Poor times at the track

    I ran last Friday at Mason-Dixon. Mod's are in the signature. The best pull of the night was only 14.1 @ 96MPH. 2.16 60' was not great, but not too bad for FWD and cheap tires. I attached a scan on the HPTuners forum since I cannot upload it here. Hopefully someone can see what is going on...I...
  6. JoshMcMadMac

    Actual Timing > Spark Table

    I was scanning on the way to work this morning, tweaking a few things. I noticed that the actual timing was typically several degrees higher than what I have in the spark table. What is influencing this? At "gentle" cruising the timing actually got as high as 50° where the table was only...
  7. JoshMcMadMac

    Question for the meth-heads

    Those running meth/water/alky injection, how do you know that it is working? I would have thought that scanning would show the engine going uber-rich at WOT, but it really did not seem any different. It seems like I am topping out at 11-12psi, and I have the controller maxing out at 10psi, how...
  8. JoshMcMadMac

    11-12PSI on a 3.1" Pulley?

    So I finally took some time out and start scanning/tuning the GTP again. I have it tuned well enough to be brave and go WOT. I still got a few degrees of knock, but nothing critical and I am still working on the tune. What surprised me was to see the boost gauge pegged at 11-12psi...I would...
  9. JoshMcMadMac

    So, I have this Clunker...

    I figure this might light a fire around here...oh, well. :lol: I realized that I had a vehicle that applied to the CARS program: 143k miles, peeling paint, body damage, etc. It has actually been in "insurance worthy" accidents five times under the ownership of my father-in-law, the...
  10. JoshMcMadMac

    TCDRacing is my hero

    Parker pulled through with a part no one else could get me, let alone getting it to me quickly...he is my new man-love. :th_laugh-lol3: Thanks again, TDCRacing. If you end up with one more, I will take that one too. :th_thumbsup-wink:
  11. JoshMcMadMac

    Windshield Washer not Working

    The windshield washers stopped working. There is fluid in the reservoir. Any ideas?
  12. JoshMcMadMac

    Slightly Hanging Rear Right Caliper

    My passenger rear caliper is hanging a bit. I replaced the rear calipers three or four months ago, as that caliper was frozen and had burned through the pads in less then six months. Now I am not certain the caliper was the issue. I bled the brakes thoroughly, and stopping is great. The...
  13. JoshMcMadMac

    Help with a Pennsylvania Inspection

    I got my cars registered in PA last week. :cool: Now I am running out of time to do the inspections, as the guy that was going to do all three cars flaked on me. The truck and the wife's car I am not really concerned about. However, my car is catalytic and smog-pump free, which fails the...
  14. JoshMcMadMac

    Tips on Removing Brake Lines

    I started the F-Body upgrade today. The SS lines are supposed to be here tomorrow, and that is all I have left to do. However three of the four stock brake lines did not want to come off. The front driver side line I had to disconnect from the distribution block under the hood. The two rear...
  15. JoshMcMadMac

    Opinions on my MAF Tuning

    I think after a few tries I got the MAF frequency dialed in pretty well. I reset and turned off fuel trim learning, so LTFT stayed at zero so I could base my tuning strictly off of STFT. What do you think? 3800Pro.com Forum
  16. JoshMcMadMac

    Car will not stay running

    The wife was driving the car home from work. She got to work just fine this morning. As she was at a light to turn from one road to another, the car died. Now whenever it is started, it sputters up to ~1000RPM, then sputters out. If I get it started, then rev it up (for example) to 2500RPM...
  17. JoshMcMadMac

    VE Tuning and Reseting Fuel Trims

    I have started with VE tuning the car. I have read conflicting opinions on reseting the fuel trims. Everything says to reset the fuel trims the first time. From there I have read not to reset the fuel trims after updating the table and starting a second scan, basically not reseting the fuel...
  18. JoshMcMadMac

    Fan Upgrading...

    With the intercooler installed it seems that the combination of 100°+ weather and the large FMHE are making the engine cooling work overtime. This got me thinking about upgrading the fans. Has anyone done this? Do we know what the stock fans pull in CFM? I would love to drop a Mark VIII fan...
  19. JoshMcMadMac

    "New Posts" Links

    I am not sure if this will be news to anyone, but figured I would post it anyway. I run around on a handful of forums each day, using shortcuts in my toolbar for each one. A lot of the VBulletin boards (the software used for this forum) have a "New Posts" link as well as the "Today's Posts"...
  20. JoshMcMadMac

    FWI without pulling the bumper.

    When pulling the bumper for the intercooler I also looked into the best way to install a FWI. I was hoping to avoid hacking on the brace that is in the way, and also hoping to avoid having to pull the bumper to ever get to the filter. I started searching the K&N site and came across the...
Back
Top