• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Search results

  1. S

    Demod Sale: Complete Stattama Turbo Kit with Intercooler and Tranny Parts

    Ok guys, I've come to a point where I am moving onto a 2014 Mustang GT. I have to demod my car as I refuse to give them all this for nothing. Instead I'll sell it as a Kit to someone on here for half price if you take the whole package together or I will later price individually. Below I have...
  2. S

    MAF Table Question

    Hello all, I am in process of fine tuning my MAF table and graphed it out looking for trends. That's where the question came in. The line is a smooth progression until 8250-8750 hertz (which is where I cross from vacuum to boost). At that point the line looks slightly like the stock market...
  3. S

    What PSI/HP is safe on 7/8"a chain?

    Hello all, I'm about to start modding my tranny. What PSI/HP is safe on a 7/8" chain? TIA, Slim
  4. S

    WOT Tuning....

    What table do I use while WOT tuning. My AF goes <10 at WOT. Do I use the PE fuel% increase table? Just curious as my LT and ST FT's are about good. TIA guys Slim
  5. S

    Rebuild Stattama T67 or buy Holset?

    Hello y'all, my T67 has an intermittent oil leak into the exhaust (only smokes once warmed up and during idle, at least that's when I see it). It's probably the rear seal, so I've been told. I checked and the rebuild will run $450 from J's Pop Shop. I'm looking at just buying a replacement...
  6. S

    Tranny dip stick bolt thread pitch?

    Hello all, I lost my nut and need to buy a new one. Anyone know the thread pattern? TIA, Slim
  7. S

    Exhaust (turbo) smoking, smells like oil...

    Hey guys, about a month or so ago I drove about 2 weeks with a major leak in my IC piping. I was easy on the car but I think I may have screwed up/overspun my turbo. Now, my boost controller is hardly raising my boost levels and I have smoke from the exhaust. It's not huge but enough its...
  8. S

    Can I tune a specific fuel cell using DHP?

    I figured I must be missing something. While tuning the MAF table it appears I am tuning the whole table on all fuel cells. What am I missing that would allow me to tune each fuel cell? TIA, Slim
  9. S

    Boost controller issue?

    I'm curious, can a boost controller go "bad"? I ask because when I attempted to increase my boost I adjusted my boost controller (BC) a quarter of the way and it raised my boost about 2#s. I wanted to hit 10#s so I adjusted further, nothing, further, still nothing, further, nothing, all the way...
  10. S

    How do I add fuel to just the decel and idle fuel cells?

    I just started my tune after installing my heads. I replaced my 22# injectors with 60# to go with the turbo but now my idle and decel fuel cells go very lean, 17+ on the WB, actually dies on occasion. I know I can correct fuel as I modify my MAF table but this doesn't add fuel in lean condition...
  11. S

    Why isn't my BOV "psssssshhhhh'ing"?

    So, I had the flange welded on, checked for leaks, none, mounted BOV, installed vacuum block, fixed leak, no more leaks, connected vac lines, drove, built boost, let off throttle, turbo sputter/surge, no pssssssshhhhhh. I don't understand. I thought all I had to do was install flange, install...
  12. S

    Throttle body spacer extended studs?

    Hello guys, I have a TB spacer but no studs. Where do I get the longer/entended studs? I think they're about twice as long to fit the TB spacer and the TB. Any ideas? TIA, Slim
  13. S

    Do you run no IAT sensor?

    I ask because a reliable source said I could and the ZZP photo of the Z7 kit doesn't appear to have one. Also my install didn't mention it. What do y'all think?
  14. S

    Stattama not building boost and I can't figure out why?

    Hey guys. I recently installed a set of ported heads, ported LIM, LS7 lifters, Intense push rods, and 1.9 modded rockers. Since the time I put it back together the car (originally an L36) runs fine with the exception that the T67 won't build boost. At WOT I stay at 5-7 pounds vacuum. I hear the...
  15. S

    Engine died during cruise on freeway?!

    I have no idea what happened other than I was cruising on the freeway. Recently I have been MAF tuning (the last two weeks) but the most recent change has been the install of a 2 bar MAP (yesterday morning) and the L67 MAP tables. I wasn't lucky enough to be logging right at the time. This...
  16. S

    Exhaust leak between turbo and turbo DP (O2's)....

    So I know this is not optimal but I have an exhaust leak between turbo and turbo DP (O2's) but I would like to start my tuning. I understand I won't be "dialing it in" yet but my LTFT are super high (likely due to my FI swap to 60#ers) and I want to at least bring those down. I will be...
  17. S

    How to test spring strength (poundage rating)?

    Hey guys, I picked up some low milage heads but I don't know how heavy the springs are (90#, 105#, 125#, etc). Is there a way to test or measure them? TIA, Slim
  18. S

    Older power tuner (1.2.3e) and UVScan download?

    Hello y'all! I was wondering if one of you could either email me the .zip file or point me to a link. I used the link I had but it was PT 1.2.4 and the UVScan was corrupt. I really need to find a more reliable scanner than 1.2.4 as it usually corrupts the files when saving it. Any other ideas?
  19. S

    Going from NA to turbo, how much do I bring timing back?

    Ok, so in my NA tune (despite being turbo) the factory has 27*-30* WOT timing. I'm getting KR and need to bring it back. My question is I don't know where to start. I know it's on the base timing, good fuel spark table. I guess I'm wondering how do I know which boxes to modify?
  20. S

    Tune timing out during shift....

    How do I tune timing out/down during shifts? I looked but don't see a particular table for it? Thanks for the help in advance... Slim
Back
Top