• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by timboku

  1. timboku

    Comp g steering rack nv7/nv8 code??

    Anyone know the difference in steering racks with magnasteer....comp g and gxps have nv8 code, SC 04plus cars got nv7...both have variable effort steering, part numbers for nv7 and nv8 are different...rock auto sells a remain ac Delco for a lot cheaper than either units and says it works for...
  2. timboku

    Plugging l26 injector holes???

    Anyone know the size npt plugs needed to block injector holes on a l26 lim? Sent from my SM-N910V using Tapatalk
  3. timboku

    dhp VIN change not taking.

    Ok, trying something not sure it will work. Have a buddy swapping a l67 into a 2000 monte carlo. I did a tune to get all the l67 stuff onto a L36 bin from a monte. It all worked but I cannot change the vin on the pcm I am trying to flash. PCM is from a GP so not sure if that is the issue it...
  4. timboku

    97 l67 IFR values same?

    Anyone know why 97gtp pcm has a flat IFR value across the board like an NA? Only year it's like that. 98 up l67s have a slopped IFR. Would it be benifical in putting slopped IFR values in a 97 that is being tuned for a turbo? Sent from my SM-N910V using Tapatalk
  5. timboku

    New to forum, not GPs.

    You can buy these and put hids in.
  6. timboku

    2003 GTP new to me. Advice?

    You can buy these and put hids in them.
  7. timboku

    Trans Issues after adding TEP VB, Input Shaft, and Chain....

    Alright been working on this project on and off for a little bit. I will try to make it short to see if anyone had input and can help. I sold my GXP so need my gtp up and running so I dont go through GP withdrawal I installed a TEP stage 2 VB, Dynotech Input Shaft, and 7/8ths 2.93 chain in to...
  8. timboku

    Zzp 3inch cat back brand new

    3inch zzp cat back..brand new never used..sold the gxp I was gonna put it on so not needed. Cones with resonator and all hardware. $400 picked up...can ship if needed at buyers expense. Located in Montgomery, il.
  9. timboku

    What size are a 4t65e checkballs and where can I get some?

    Lost a smaller check ball from the case cover. Anyone know where I could get one and or the size of it? Thanks
  10. timboku

    1.8 SLP rockers with XP cam or VS Cam

    Can you run 1.8 slp roller rockers with an XP cam or VS cam. Have the opportunity to get some for a decent price and was wondering if you can run the rockers with either of those Cams. The gtp has a XP cam in it and I will be building another engine for my Cutty project that will have a VS...
  11. timboku

    Don't put your SFI balancer on wrong or boom goes your exhaust..lol

    Late night putting build back together..long story short there are 2 notches in a SFI 8 rib and apparently I put it on the wrong one cause this happened at midnight last night when I was cranking it... Loudest bang ever in a garage...I have seen a different post about mufflers blowing out...
  12. timboku

    Double Roller install help.

    Putting my double roller on. Does the crank gear need to be hit onto the crank? The stock one slid off with my hand. The DR crank sproket seems like it barley fits and needs to be hit on with a big socket. Also, I line up the 0 marks on the gear as well so the 0 is facing up and the dot on...
  13. timboku

    What is the replacement core for ssic

    Anyone know what heater core or replacement core is used in zzps ssic? Can locate any info on it.
  14. timboku

    Sale Injectors, modded rails, 1.9s, mps pullies,and more.

    Looking to get rid of a few things. Everything works just upgrading. GPOs....Never installed and in primer $155 Shipped. SOLD 42.5 lucas injectors ev1. Under 10k. $115shipped. SOLD 1.9 modded rockers. Not sure the brand got them off a firebird v6 group. Ran for 30k no issues. $200...
  15. timboku

    Got my Tep parts any good write ups

    Got my TEP parts today so time to throw them in trans. Any good write ups on installing valve body, 300m, 4th gear clutch, and a 7/8th chain? Trans will be out of car. I have the manual seems straight forward but just wondering any tips or tricks to watch for. First time tearing a Trans open...
See more
Back
Top