• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by RICE KILLER

  1. RICE KILLER

    snout bearing replacement

    I have searched everywhere for info on rebuilding my gen v snout and the only thing I can find is info on the gen 3. Im not sure if they are the same. All I need to know is how to safely get the shaft out of the snout casing and I should be able to get it from there. For the gen 3 I read that...
  2. RICE KILLER

    surging?

    so heres whats going on, when i start my car especialy when its cold it likes to surge, sometime all the way up to 1500rpm then it will run steady for a while with a few random surges. is anyone elses having this problem? suggestions? look at my signature for mods thanks very much for any help
  3. RICE KILLER

    take a look at this scan!

    ok so im stumped. my friend and i friend from the local club (MN ClubGP) went to start tuning my car and this is what we saw... the o2 was reading in the 100mv range and below at WOT The LTFT's where locking at 16.4+ while cruising, then lock in 0 in PE. i was thinking that it could...
  4. RICE KILLER

    LIM Gaskets

    so i am tearing into the top half of my engine in the next couple of days here i am about to throw on a a ported s/c, zzp billet TB, ported LIM, modded and polished L26 fuel rails, and just clean everything up. also it has newer LIM gaskets like 2,500 miles, can i just re-use those? also...
  5. RICE KILLER

    injectors yet?

    so i am running an xp cam with all the goodies, fwi, headers with a 3.4 and all the other basic sporting mods. i plan on doing either a N* TB or a ported stock TB, ported SC, and ported/polished LIM and hopefully drop to a 3.2 with a tune. so heres my question can i run the stock injectors or...
  6. RICE KILLER

    blower porting?

    i have been working on porting the outlet of my blower using a rotary file on a router. so far i have removed the H-Bridge opened up the outlet and just cleaned everything up. Question #1 on the outlet itself after porting it it leaves a sharp 90* angle. will this cause turbulence inside the...
  7. RICE KILLER

    what pulley?

    ok so i am about to start ordering parts for my gtp :th_thumbsup-wink:and here is what i am going to do as far as mods. -FWI -SSAC headers -1.9 rockers -ported TB and SC -DPH PCM -180* T-stat -104 autolites and new wires -modular pulley system so i was going to go with the 3.4 pulley but do...
  8. RICE KILLER

    what pulley?

    ok so i am about to start ordering parts:th_thumbsup-wink: for my gtp and here is what i am going to do as far as mods. -FWI -SSAC headers -1.9 rockers -ported TB and SC -DPH PCM -180* T-stat -104 autolites and new wires -modular pulley system so i was going to go with the 3.4 pulley but do...
  9. RICE KILLER

    best scan tool for $200 0r less

    what is the best scan tool for $200 0r less? should i go hand held or pc based?
  10. RICE KILLER

    tune?

    ok so a am about to start modding a 2000 gtp and here are the mods i plan on doing FWI, ssca headers, 104 autolites, 180* T-stat, ported TB, ported SC inlet and outlet, 1.9 rockers and an aeroforce scan guage. so my questions are should a vendor pcm be a good choice of so which one? i have had...
  11. RICE KILLER

    good combo? suggestions?

    ok so i just got a 2000 gtp and am looking to start modding. i was going to start with all the preventative maintenance synthetic oil change, sc oil change, tranny flush/filter, coolant flush, clean lim,and replace all gaskets along the way etc. now for the mods home made fwi from the plans in...
See more
Back
Top