• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by nukkinfuttz

  1. nukkinfuttz

    Flashing CEL but NO codes! ???

    This is going to be a fun one... Today the engine started to misfire under moderate loads. It truly feels like a misfire, and if I set the parking brake out it in drive and give it some gas it constantly misfires. the CeL also blinks when I do this. much to my amazement, there are no codes...
  2. nukkinfuttz

    Help with Rod Replacement... yes I searched.

    First off... if I search Rod, it fails because the word is too short. second, if I search connecting rod, or piston rod, the search only searches for Connecting, or Piston, and NOT rod. So, I must start a new thread for something that has likely been answered a hundred million times, but...
  3. nukkinfuttz

    Help with inner tie rod boot

    I was replacing my inner tie rods and just went ahead an picked up new boots to go with the job. So, when I took the old one apart, rather than unscrew that jam nut that holds the outter tie rod end so I could get the old boot off, I just cut the old boot off with a box cutter. Fast forward...
  4. nukkinfuttz

    car wont stay running longer than a few seconds

    I was out and about today and i noticed my check engine light came on. There were no drivability problems. I headed home and about 3 blocks away from there the car just cut off. I could restart it immediatley, and it would run fine for a few seconds, then stumble and cut off agian. I went...
  5. nukkinfuttz

    3.5" pulley

    if you had say a completely stock engine, which according to what i can find, should run about a 14.9 if you hold your mouth just right... what should be an expected ET by adding only a 3.5" pulley? Thanks
  6. nukkinfuttz

    Wire harness

    My 98trans wire harness crumbled when i tried to remove it. I then ordered a 19few pin connector wire harness on accident Of cousr i really needed the 14 pin for my year. Well i go to the trans part store and ask for a wire harness and they bring out a "universal" that will worl with all...
  7. nukkinfuttz

    RPMs bouncing when cruising

    Im driving along on flat level interstate at and the RPMs will sometimes start boucning like 100-200 RPMs on the needle. I also feel it in the seat. Its a very rythmic pulsation, like a sine wave or something. I give it some gas, and it may clear and not come back, or it might return. If i...
  8. nukkinfuttz

    New Car. What should I be checking?

    Hi all, I just picked up a 97 GTP that I am loving. its got really high milage, 250K. Its really clean inside and out, the owner took really good care of it, but I figured I should come here and ask you guys what you think are high fail items that I need to be checking out? I see that Vacumm...
  9. nukkinfuttz

    Transmission Cooler

    I want to add an external trans cooler this weekend. Whats a good size to get? They get more and more expensive the larger they get, so i want to be sure i buy the one i "need" and not one for a cummings diesel or something rediculously large. Any recommendations?
  10. nukkinfuttz

    I been had... New car, bad trans.

    I just picked up a very nice/clean 98 GTP. The test drive went well, the guy seemed to be babying it, but i though he was just a dork and didnt really get into having a fast car. this thing was clean as a pin and I just didnt get the impression he would be the type to romp on it. Well, we...
See more
Back
Top