• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by jacobmh27

  1. jacobmh27

    Possible TCC RPM Problem

    On the Highway in very light throttle and right around 2000 RPM the Tach will jump a few hundred RPM. Just a touch more gas 2200 RPM no problems. Trans rebuilt about a year ago.
  2. jacobmh27

    01 GTP Coolant Leak

    Replaced the Leaking water pump on my GTP. This stopped the dropping on my driveway. Ran the car for 1 hour and no leak. Then I drove the car 600 miles and my low coolant light came on. Needed a half gallon to fill it back up. I did check the Coolant level after I replace the water pump to make...
  3. jacobmh27

    P1629 and P1673

    P1673 Description ENGINE HOT LIGHT CONTROL CIRCUIT Output Driver Modules (ODM) are used by PCM to turn on current-driven devices needed to control various engine and transaxle functions. Each ODM can control up to 7 outputs by supplying ground to device PCM is commanding on. ODMs can diagnose...
  4. jacobmh27

    HUD Speedometer

    Tried Searching many of the Sub Forums but could not find anything. My Speedometer in the cluster is working fine. But my HUD is all over the place just scrolling diferent Number all the way from 0 to 199. Scrolling very fast. Scolling even at Stop with Car in Drive. Any Ideas??
  5. jacobmh27

    Thinking about get this set

    KYB Strut and Coil Spring Assembly SR4002 Seems like the set would be easy to put in. I donot really want to drop the car any I have enough problems with hitting my ubend on my SSAC headers already. I am afraid if I drop it any more I will not have one left. If these are not a good idead let me...
  6. jacobmh27

    Oil Pan Gasket

    How hard is it to get the oil pan down to replace the gasket I see something blocking the passside frombeing removed looks like thereare2boltswill that comedownoris thatthe motormount.
  7. jacobmh27

    resonator

    My resonator is leaking and I need a new one. I have a stock cat back so far. Looking to see my options. Mabey a cat back or just the res. Any options you all can think of. Is there going to be a differance if I do the Whole cat back. what about no res and a cat back with no Res???
  8. jacobmh27

    SC Fill Plug striped

    Basically what the title says. I was going to change the fluid in the SC for the first time i have owned the car and I noticed the Allen hole is stripped. Any sugestions on how to get it out with out drilling. Dont want to get any pieces in the SC.
  9. jacobmh27

    Bottom Door Molding

    Where can I find the Plastic Clips that Hold the Door Molding to the Metal Plate. THe Plate came Completly off and GM wants me to buy the whole Molding because they will not sell me the CLips seperate.
  10. jacobmh27

    idle Problem

    I seems that when it is cold and I first start the car the idle goes up and down till the car warms up. My mods are in my sig. Just don't know what it could be.
  11. jacobmh27

    SSAC Heade Tick

    Other than replacing the Flex Pip e with the one from ZZP I think it was. Is there any other way to at least reduce the Tick. Like wrap or something??
  12. jacobmh27

    case Learn

    Anyone delt with a case learn on a PCM from WIll. I am trying to do it with my Aeroforce and the Code will not go away. Any Suggestions
  13. jacobmh27

    Overkill PCM Case Learn

    Well just got a PCM from Overkill and it is giving me the P1336 Code on my Aeroforce. I tried to do a case learn put Ebrake on and then hold break down bring RPMs to 4 to 5K Rpms in 4 to 5 seconds When it hits the Litimer then let Idle Then shut off car for 30 Seconds and then start car...
  14. jacobmh27

    3800 vs DHP PCM's

    I hear that these are very Close togeather. It seems that Overkill PCM that I paid for 3 weeks ago is not comming. I have emailed Will at least 6 times over the past 3 weeks and no respose. Whatever Moving on. Looking at these 2 PCMs and wondering what way to go. It cost to must for dyno time...
  15. jacobmh27

    HELP Installing Pulley

    I am trying to get ths pully back on using the Pulley puller sent to me by 3800 Performance and I broke the 2 little bolts that hold the large bolt in place. I have about a quarter inch to go. I am using grease to keep everything moving for the bolt the Shaft is not moving I am using a bar to...
See more
Back
Top