• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by bocou92

  1. B

    Something missing

    I recently gave my car to a tech to install the zzp inner cooler kit and fuel rails. After finally looking at everything I notice something missing, or just probably was never there. Car runs perfectly fine The part is to the right of the tps somewhat above the tstat. Could someone tell what...
  2. B

    Fuel Pressure Dropping at boost

    My car is with my mechanic getting a dyno and everytime it starts to get boost, fuel pressure drops. Just got the zzp 3.4 pulley, zzp fuel rails, and stg 2 intercooler just added. I've been riding with full zzp exhaust 3", their ECM upgrade, and Cai. I've replaced the pressure regulator which...
  3. B

    Transmission fluid in power steering

    Had a friend take my 02 gtp into a shop to change out the steering rack last month, and i noticed the steering was stiffer. Found out that there ATF in the P/S resv. Is ATF a sub for power steering fluid?
  4. B

    Does it need a Tune?

    So I'm getting ready to buy an intercooler for my 02 GTP with ported LIM, and ported S/C. Would i need a tune for these? Also, I'm planning to reduce my S/C pulley to a 3.2", but don't know what size of fuel injectors and what kind of fuel pump to get? Any advice?
  5. B

    Building Strut Assemblies?

    Thinking about getting some new struts for my 02 GTP and trying to figure out if it would be cheaper to build your own strut assembly are just buy a fully complete one. Don't really want lowering springs cause my damn down pipe is low enough to start scrapping after going over speed bumps, just...
  6. B

    rpm drops when coming to a stop

    When come to a stop my rpm drops and then smooths out. It drives smoothly on the highway. Starts up smooth too. I got a 2002 gtp. Any ideas?
  7. B

    Need Files for tuning a 2002 GTP

    I have a friend with a HPT tuner and is willing to flash tune my car. Does anyone have a .bin file that has matching mods for my 2002 GTP and other good add-on stuff? SD Headers w/EGR ZZP 3in ehaust without cat CAI
  8. B

    need tune for 2002 gtp

    Anyone have a tune for a 2002 gtp with these mods: Cold air intake 160 thermostat Speed daddy headers Zzp 3" stainless steel cat back with cat
  9. B

    trying to add door panel trim lights

    My 2002 GTP 4door didnt come with the door trim lights on the doors and wanted some advice on how to rig and install the lights?
  10. B

    Door trim/molding loose

    my door trim is coming loose and i thought i needed new clippings for it. found out that its just glued on to the door. what the hell kind of glue is used to keep that thing on there that wont **** up the paint for metal on the door?
  11. B

    windshield wiper spray problem

    i got a problem with my windshield wipers not spraying. just change the washer pump 2x to make sure the first one might be bad out of supply. i was wrong. tried to shoot the harness but i have no clue what im doing. any ideas for me on how to shoot the harness from the washer pump?
  12. B

    issues with SSAC header

    i just got some SSAC headers this morning and should be in by next week. i was wondering if any of you motorheads had any 'issues' fitting them in and what you did to fix it? i.e o2 sensor hitting the bottom of the floor, crossover to short, exhaust leaks, bad clamps. ps im guess SSAC is...
  13. B

    cold air intake

    cant decide weather to get a k&n cold air intake or zzp cold air intake. what do you guys run on your 3800 SC?
  14. B

    P0171 code after intake gasket change.

    holy crap! just found the solution by looking at your pic. im missing THAT hose can u tell me where that hose goes? perferably a from - and - to pic
  15. B

    P0171 code after intake gasket change.

    this is what happened... while changing intake gasket, the rubber T that connects the vacuum lines broke and so i rigged a new one <- might be the cause when pulling out fuel rail and injectors, some wierd plastic piece on bottom after the o-ring broke. no leak cold be found. right after the...
See more
Back
Top