• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by bevernden

  1. B

    Best way to compliment 1.9's?

    I plan on buying a set of 1.9 roller rockers (w/LS6 springs) and was curious if it's best to run a smaller s/c pulley or adjust the tune to get the most out of the rockers? Current mods: CAI, 3.4" pulley, headers, 3" downpipe w/ high-flow cat, PCM tune
  2. B

    How to remove A/C high side service port?

    I've got a leak in the A/C high side service port and need to replace it. I had assumed that I just use two wrenches, one to hold the hex welded to the high pressure line and the other to loosen the valve. I feel like I'm going to twist and break something. Am I doing something wrong? Can...
  3. B

    Modify Overkill tune?

    I'm still going through a bad experience with a tune from Will at Overkill. Long story short, I'm experiencing two issues with the tune: surging idle after cold startup for approximately 2 minutes and shifts that are firmer than what I prefer. Overkill's website says that all of his tunes are...
  4. B

    Will please call me!!

    Will- I've tried emailing you several times within the past month and have not received an answer to resolve the PCM issue. I've also left several voice mails to 647-403-1297 with no response. I'm still looking to get my PCM back as well as my $100 credit. Please contact me as soon as...
  5. B

    High-flow cat and rear O2

    I've check the archives and don't quite see what I'm looking for. I finished installing a set of ZZPerformance headers with a Magnaflow high-flow cat and now I'm getting an SES for poor cat performance. I'm about to order an Overkill PCM but want to know if it's possible to modify the program...
  6. B

    What to do after headers?

    I just finished installing ZZPerformance stainless steel headers and 3" downpipe with high-flow cat. I also did the machine LIM with the intention of machining the supercharger housing in the future. My question is what to mod to take advantage of the headers? Should I get a re-tune (I have a...
  7. B

    Intake gasket w/ RTV?

    I had the coolant leak with visible coolant in the injector valleys on both sides of the engine. Once I removed the LIM, I inspected the gaskets and was surprised to not see cracking, damage, missing rubber inserts...or anything that would lead to leaks. I got my hands on a new set of OEM...
  8. B

    Ported LIM, cut gasket to match?

    I'm installing a machined LIM since I'm in there fixing a coolant leak. I have a Felpro plenum gasket which obviously has the openings to match the OEM LIM. Have most of you cut the gasket to match the machine LIM?
  9. B

    ZZP PCM's

    I read that you are affiliated with ZZPerformance.com. Are the PCMs they sell your's? Is that the best way to get one if I live in the states? I have a 3800performance.com PCM. What would I benefit by using your PCM tuning?
  10. B

    Pacesetter header dyno numbers?

    Does anyone have any dyno numbers for the Pacesetter headers? If so, please list what mods you had done at the time. Thanks!
  11. B

    Pacesetter headers experience?

    Does anyone have experience with the Pacesetter headers available at zzperformance.com? Fitment? Dyno/track results? Installation issues?
  12. B

    Downpipe or Headers?

    Just curious what you guys might recommend. I'm currently running a cold-air, 3.4" pulley, colder heat-range plugs and programming PCM. I was ready to purchase a downpipe but was wondering if headers would be better. About the only other major engine mods I'm considering are rockers...
  13. B

    Fuel rail mods for intercooler?

    I'm considering purchasing ZZPerformance short stack intercooler and don't quite understand what I will need to do to the fuel rails. Can someone clear that up for me?
See more
Back
Top