• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by BDEGhost

  1. B

    How to remove fan switch

    Hi guys, I am asking for your collective wisdom on how to get to the mechanical fan switch for the heater/AC. I have seen some info on removing the plastic of the dashboard to get to the radio, etc. but it didn't seem to be directly related to my car. ('02 GP). Specifically, if someone can...
  2. B

    Opinions on CV Joint Repair or new half shafts

    If this is not the right forum for this question, please move to proper one. Yesterday, while replacing my front brake rotors and pads, I noticed that the driver's side half shaft boot closest to the tranny was slinging out green grease onto my lower frame. Not a lot, but enough to scrape off...
  3. B

    Engine surging, hesitating (It's Fixed !!!)

    About a month ago, I replaced my LIM gaskets (with aluminum ones), new UIM (Dorman) new gaskets, pcv, etc. (Thanks for all your help on my doing this) After this, my car ran really strong for the first couple of weeks, and then I noticed hesitation when pulling hills. On the flat, it ran well...
  4. B

    AC Delco plug wires

    I am in the process of changing out my plugs and wires and I have a question. I have purchased AC Delco plugs and AC Delco wires. In the box with the wires, there is a clear tube of something. It doesn't say what it is. Just a warning about not eating it in a couple of languages....LOL. I...
  5. B

    ZZP O2 sensor any good?

    Like the title says, are the O2 sensors that ZZP sells any good? I need to replace my rear one since I am getting P0141 code repeatedly even after I reset it. Sometimes, it will take a day or two for the code to come up after being reset, and sometimes it comes up almost immediately. I am not...
  6. B

    Need help with fuel lines

    Well, I have completed my upper end rebuild with new lifters, LIM gasket (aluminum), new Dorman UIM, gaskets, etc., etc., etc. After putting it all back together, oil change, AF flush, new Prestone yellow AF, the only remaining problem was the connection where the pressure fuel line connects to...
  7. B

    Which Threadlock to use?

    I am ready to start re-assembling my LIM, UIM, etc. and I am wondering if you experienced people can give me some guidance on which sealant/threadlocker to use? The GM tech manual says to use GM #12345493 which is the same as RED Loctite #272 on the LIM bolts. This is the high strength Loctite...
  8. B

    Top of LIM full of oil

    When I pulled off my UIM today, I was surprised to see that the 2 deep wells in the opposite corners of the LIM where the 2 hidden bolts are, were filled to the top with oil !!! I am fairly certain it was pure oil, not mixed with AF. There was no sign of a crack or blowout on the UIM where the...
  9. B

    Fuel Lines O rings

    I tore down the top of my engine today to replace my LIM gasket and UIM & gasket. I am also replacing my lifters. When I went to disconnect the plastic fittings on the fuel line where they attach to the fuel rail, I noticed that when I moved them even slightly, a small amount of fuel leaked...
  10. B

    Any secrets to changing wires?

    I am in the process of changing my LIM gaskets, new set of lifters, new UIM/gaskets, etc. and I wanted to change my plugs also. They are original, at 112K miles, still run OK, but figured I should change them. My problem is that I have been trying for over an hour to get the wires off of the...
  11. B

    Rocker Arm Bolts

    Today I received my order from ZZP for a rocker arm install kit. The picture of the kit shows 2 valve cover gaskets, 12 TTY bolts and ARP assembly lube. When I opened the box, instead of 12 TTY bolts, I received 12 re-usable bolts.:( Can anyone enlighten me on what the difference would be if...
  12. B

    Which lifters to buy?

    Hello all, '02 Grand Prix, 3.8L N/A I am doing a LIM gasket replacement and a new UIM w/gasket, valve cover gaskets, etc. Since my lifters have been "ticking" for a while now, I figured I would replace them as well since I would have it torn down anyway. My question is: what are the best...
  13. B

    EGR Gaskets?

    I am gathering parts needed to change out my LIM Gaskets. I can't seem to find whether I need a new gasket for where the EGR pipe connects to the LIM. It doesn't appear to be included with any of the LIM gasket sets. Is there one? And if so, do I need to replace it? Also, I am still...
  14. B

    Spark plugs, etc.

    I am looking for the collective wisdom of all of you. I am in the process of gathering parts to replace my UIM and gaskets for the LIM and valve covers. I have read a lot of stuff about the original LIM gaskets being eaten up by the DexCool coolant and that if I am replacing them, I should get...
  15. B

    Dorman Intake question

    Hello all, I have ordered and received the Dorman intake manifold that I plan to replace on my 02 GP N/A. It looks pretty complete with all necessary gaskets, o-rings, etc. but I have a question. In the middle of the gasket assembly, there is a plastic tube (about 1/4" dia.) that is about 9...
See more
Back
Top