• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by Andrew_99GTP

  1. Andrew_99GTP

    2002 bonneville won't start

    My cousin brought her car to me because it was running rough. Found the coil pack for 2 & 5 wasn't firing. Swapped with a good spare coil I had and had the same issue. Swapped in a good ICM and the car wouldn't start. Put the original ICM in and it still won't start. There is now power to the...
  2. Andrew_99GTP

    gasket kit

    I have my engine out and will be replacing all the gaskets while it is out, where is a good place to get a complete gasket kit?
  3. Andrew_99GTP

    Are a 99 and 01 HD trans the same?

    I found a 01 HD trans for sale locally and I was wondering if it would bolt in my 99 GTP. Also is there a way to tell if the trans is a HD trans by looking at it?
  4. Andrew_99GTP

    ATC forums?

    Does anyone know of any good ATC forums? I currently own an 81 Honda 250R ATC. I am also looking at picking up an 85 Honda 250R ATC in the next couple of days. Just thought it was time to join a forum. Thanks
  5. Andrew_99GTP

    Electrical switches?

    I am looking for a good place to buy electrical switches and connectors. Does anyone know of a place online? I need a 3 position, momentary ON, 6 pin switch.
  6. Andrew_99GTP

    What a night

    Took the gp out tonight to do some more tuning and see if the trans was still shifting better. It seemed to be running pretty good in the beginning of the night but it seemed as the night went on this got worse. The car started shifting horribly and sometimes not shifting at WOT or close to it...
  7. Andrew_99GTP

    Hesitating shifts

    Ever since I went turbo my trans does not like to shift. Under light throttle it isn't as noticeable and med you can just notice it. But at WOT it is really bad. I will get to the point where the car should shift and it will just hold the rpm for a sec or two and then shift. When it does this at...
  8. Andrew_99GTP

    Those of you with DMH cutouts?

    How long did you tell them you wanted your harness?
  9. Andrew_99GTP

    Deleting the EVAP

    I have been thinking about deleting the EVAP on my car while it is apart. I would do this mostly to clean the engine bay up but is there any other advantages of this. Also if you did this how did you go about doing it?
  10. Andrew_99GTP

    Is it possible to run without an O2 sensor?

    I saw in a post where a guy was not using the O2 sensor and running in open loop all the time. How would you go about doing this and is it safe?
  11. Andrew_99GTP

    Anyone running an EGT sensor?

    Just wondering if anyone is running one and has it been beneficial? I am thinking about getting a plx EGT sensor because I already have a plx w/b.
  12. Andrew_99GTP

    Fuel Economy???

    I ran across while skimming the turbo section. I am not posting this to bash the guy but just thought maybe some of you over here would like to follow this one. I am curious to say the least but doubt it will work. ClubGP Message Forum troubleshooting
  13. Andrew_99GTP

    Reccomend me an air compressor

    I am looking at getting an air compressor because I am getting tired of not haveing one :th_winking:. I am looking for something around the size of an 80 dual stage 240v. The problem is they are so expensive. I plan to use it for an impact, die grinder things of that nature. Shouldn't be doing...
  14. Andrew_99GTP

    Why is there still KR?

    I am helping a friend tune his car and we finally got to the point were his trims are looking pretty good. So we though would check out his WOT. He has some KR which we didn't think was too bad and could be tuned out. But then we looked at his O2's. With them being that high can we really give...
  15. Andrew_99GTP

    Timing a double roller?

    I made a post a while back asking how to time a double roller. http://www.grandprixforums.net/f18/timeing-a-double-roller-setup-2352.html I am sitting here with my stock gears and my JP double roller gears trying to figure out how they are -2* different. I laid the cam gears on each other and...
See more
Back
Top