• The site migration is complete! Hopefully everything transferred properly from the multiple decades old software we were using before. If you notice any issues please let me know, thanks! Also, I'm still working on things like chatbox, etc so hopefully those will be working in the next week or two.

Recent content by abrahamhuerta95

  1. A

    l67

    Reasonable price for a 142k long block? Out of a 2000 gtp
  2. A

    Rod Knock

    It's been a while since my last post but unfortunately I recently got a rod knock on my 97gtp it had 208k miles with a 3.4 with supporting mods except a tune. Sometimes I had 5-6 kr at WOT, 2-3 or even 0 at times. I'm just looking for some advice on what to do. I'm not that experienced to do an...
  3. A

    ignition timing

    I couldn't find the thread on ign timing on 97 gtp's. 5fingerdeathpunch said something about the readings being backwards? Anyone care to shed more light or point me to the thread on this topic. At idle it sits around -16 and climbs up to -22.
  4. A

    al104

    What's the heat range on these and what are they supposed to be gaped too?
  5. A

    kr

    Pulley'd up to a 3.5 still have 3° of knock at WOT. I also lost 2-3lbs of boost at WOT. Maybe its the weather? But 3° of knock with headers something doesn't seem right. I got new stock wires, al104 180tsat my o2 isn't hitting the firewall... 207k miles no check engine light. I'm still waiting...
  6. A

    tune

    How much should I expect to pay for a tune? 5° of knock at 11lbs full throttle on a 3.4 with headers 91 gas.
  7. A

    tune

    I'm a huge noob on this subject. My local tuner has no programs for our platform. Is there such a way were I can buy a tune/file specific for my mods and have him run it on his equipment to run on my car? I have a 97 gtp with 208kmiles on a 3.4 gen3 with headers and a cat (no check engine) with...
  8. A

    HELP!

    Okay so in the process of lowering my car from the jack it hit and bent my oil pan breaking the sensor inside the oil pan. I assume this cuts something off because while driving the car would stall really bad and my kr would sky rocket. We got the new sensor but the problem is the new sensor...
  9. A

    headers

    Best way to put on the rear speed daddy headers on a 97gtp?
  10. A

    axle's

    My 97 gtp at 207k axle's make a cracking noise when turning. I've driven it a lot less since the noise began and was a bit more easy on the peddle. I'm installing my headers tomorrow with a 3.4. Might as well replace the axles before they break. Should I go with the local autostore ones? I kind...
  11. A

    i have kr!

    Wow. I couldn't believe it. I didn't bother getting a way to kr until I got my 3.4. So I added the kr gauge to my scangauge 2 and I had 3.7* of kr at full throttle 6,500rpms... Currently on a 3.5 pulley gen 3 with the following mods: front plog, ubend delete, al104s, new plugs, high voltage coil...
  12. A

    3.4 pulley belt

    Where is the best place to purchase a belt for a 3.4? Currently on a stock belt on a 3.5... Do local auto zone carry these? I looked on zzp and it seems to complicated and a lot of reviews claim they give you the wrong belt.
  13. A

    headers

    Here goes another noob question. What kind of cat do I run with headers? Speed daddy's more specificly. Can I just reuse my current cat since it's fairly new?
  14. A

    tuning

    Anyway to find 3800 tuners locally? Is there a 1800-tuner number available? Haha the closest I found was a 3hr drive to Los angeles. I'm in California by the way. I tried Craigslist any other ideas?
  15. A

    97 gtp vs 2010 Chrysler 300 hemi

    I knew I was going to lose just wanted to see by how much... 20 roll I took off first looked like I had the lead but once we approached around 90 he gained in me and pulled a car and a half. Heet off at 120 I was at 110. My mods 3.5, al104, custom CAI, high voltage coil packs, plog, ubend. And...
See more
Back
Top