The *Unofficial* GPF RC Thread

[ItHurtz]

if you want to be FANCY
http://www3.towerhobbies.com/cgi-bin...?&I=LXKSC1&P=7 x2

http://www3.towerhobbies.com/cgi-bin...?&I=LXKSC2&P=V

[Matt Palm]

So order 2 sets of link 1 and 1 set of link 2

[ItHurtz]

ya

http://www3.towerhobbies.com/cgi-bin...?&I=LXCPTN&P=7

if you wanna be a cheapy
http://www3.towerhobbies.com/cgi-bin...?&I=LXNWS2&P=7

just make sure they fit on your axle, 6mm I think.

[Matt Palm]

or these
http://www3.towerhobbies.com/cgi-bin...?&I=LXUTG9&P=V

[ItHurtz]

si those are nice

[Matt Palm]

purchased

[ItHurtz]

the traxxas wheels dont fit into an aftermarket 17mm hexes ( traxxas wheels have the spline inside and can only be use for traxxas spline 17mm hex)

[Matt Palm]

So they wont work?.....

[ItHurtz]

No it works. You ordered the splined hubs which will fit ANY 17mm wheel out there.

Something with traxxas certain wheels where if you have a HEX hub, it wont fit SPLINED wheels. No worries, splined fit hex and splined.

Didnt mean to scare you just though I would throw random fact in haha.

[Twizted 1]

I sure hope you've already upgraded the hell out of that Maxx, because if you plan to run that system in it even on 3S it'll desroy it if on stock parts.
I made that mistake while back when I bought a Monster system. It was a *****ING BEAST on 4S . I never ran 6S through it so I can just imagine what its gonna be like.

[PurpleGuy]

So those adapters up there would allow me to run a 17mm hex wheel instead of the stock 13/14 whatever it is? That'd give me more options and allow a bigger tire for the snow

[Matt Palm]

I still have the stock drive lines and everything lol i figure ill kist fix it when i snap everything

[PurpleGuy]

Hooray for steels. I snapped 3 of the stock plastic ones with a stock motor on 3S

[Twizted 1]

I still have the stock drive lines and everything lol i figure ill kist fix it when i snap everything

I feel sorry for your maxx! Lol
It'll be a LOT of fun doing it though!



Reptile DHP ecm, ported SC, ported and blocked LIM, SD headers, 1.9 Harland sharp rockers, HAI

[Matt Palm]

ive been running 2 2s lipos on my stock esc and motors.

[Twizted 1]

But that wasn't the monster! Lmao
Have you ever run a monster combo before?
I put one in my modded 4x4 slash and it lasted 10 mins! Lol
I can tell you this, if it had wings it would have took flight!



Reptile DHP ecm, ported SC, ported and blocked LIM, SD headers, 1.9 Harland sharp rockers, HAI

[Matt Palm]

first time for brushless lol. but i did buy a wheelie bar. It stands up now i can imagine it when it gets the motor swap

[Twizted 1]

Lmao, I don't know if I would put that wheelie bar on just yet.
It'll do standing backflips if geared correctly.

If you've never run brushless your in for a BIG surprise.
Ive gone brushless in everything I own.
Ill never go back!

Get it installed I'm anxious to see pics of the carnage! Lol

[ItHurtz]

He wont get carnage pics, the shafts will keep snapping. If some how he gets it off the line the next tree or wall he see's will end its life.

[Matt Palm]

first i gotta get connectors to solder on. then i gotta figure out how to solder them