Thread: Starting to build up the intrigue, finally

This doesnt sound to reassuring..

It's okay Max. I'm here for you.

Max must be super busy. He had told me he was going to post Wed night.

Short story made as long as I can:
Wed the 2nd I recieved a call that he thought something went bad in the valve train when taking some coworkers out to lunch. Erich then called with a dead motor at about 3pm. By 7pm two dead cars had been delievered. Both parked until Saturday.

Saturday: Max pulled the plugs to find one electrode beated closed. Erich arrived with a motor. While Max plugged away at hsi disassembly Erich and I pulled his and started swapping parts to the new motor. (heads, cam, oil pan, intake, everything except the shortblock.) By the end of the night Erichs was ready to go back in and Max's was ready to pull out and put on the recently emptied engine stand.

Sunday: Pulled Max's, slapped it on the stand and he pulled the other head off. Erich's was back to running and left.

Monday: I get out of work a couple hours before Max and jumped on it. By the time he arrived his old L36 was on the stand and stripped to the shortblock. He tossed in the cam, oil pickup and prepped all the block surfaces for reassembly.

Tuesday: I did a radiator hose on someones car, then hopped to it. Max arrived to find one head awaiting torque and me cleaning the other. He got those torqued down, soon as he did the first final pass I had the pushrods in and was torquing the rockers, intake went on, we were hauling some major butt........then realized we didn't have front and rear engine cover gaskets. Order placed...damnmmmmit!

Wed: Max arrived early and found the motor sitting in the cradle. To prove it, I disconnected the hoist. From then until 9-9:30 we installed the headers, intercooler core, SC, TB, hooked up the wiring, PS pump, AC compressor, starter, TC bolts name it.. at 9-9:30 he turned the key and it roared to life again. We high fived and called it a night after running it up to temp and topping off the fluids. It's ready for an oil change.

Thurs-Sun: Max is busy with good stuff and on Sun he'll be by to pick her up. Had Erich's not been there, it probably would have been a two day turn around and run on Sunday.

What the hell happened to beat the spark plugs closed.

maxed out the timing but didnt back anything off for safety, then had a car full of people.

its ok max, yours lasted longer than my is3 build the second time. blew it on the dyno within 24 hours of being completed...

That sucks. I'm still really looking forward to seeing this beast

Sent from my DROID RAZR using Tapatalk 2

Don't fret it is being rebuilt.

Originally Posted by Nighthwk12

Don't fret it is being rebuilt.

Correction:..completed Wed night.

Bill don't **** around people, he gets the **** done.

If anybody has ever met bill he has arms that could put Barry Bonds to shame LOL

Damn that blows... Hopefully the L36 holds up!

It will. I'm going to hide the car from him so he can't blow it up.

Time for some E85 this time, help prevent another accident.

Max + higher compression = a horse of a different color

Well..the head came off and the piston was chipped. When you say data to back it up, no recording was being done at the time of the failure.

I thought pistons weren't all that hard chip depending on how much detonation you have. And I remember Max saying he had 0* KR? If he chipped one on his L32, wouldn't his L36 be more vulnerable under the same setup?

Man i'm sure mine are chipped. I just hope my car holds up until I can start my build.

Signs of a chipped piston.

1. Car runs bad, you pull plugs and find one or more electrodes smashed.
2. Pieces of piston on top of your IC core. They can come up through the bypass hole of the SC
3. Visual confirmation

From research and chatting with others, apparently GM didn't gap the rings on the L26 and L32 as much as the predecessor engines. Therefore it's easier to chip a piston.

Max should be returning from a trip today. Likely we'll hear from him.