o-ring.. can cause the issue.
|
|
08-02-2012
o-ring.. can cause the issue.
08-03-2012
Honey Badger gives no ****s.
I bought a new Wizaired CAI from ZZP. this one is fitted with the correct tubing for the Northstar with the right length.
the old was was a GEN 1, and beat to **** because i got it used.
08-07-2012
Still waiting on that intake from ZZP,
While im waiting as far as the inter cooler tubing goes this is my understanding of it.
Bottom of the left side of the FMHE to 90* bend to top of I/C pump (Bottom line from I/C pump goes to LEFT OR RIGHT port on the intercooler?) and the oposite will be the return line. and the port on the Top of the FMHE goes to the tube you pour in?
08-08-2012
Intake from ZZP arrived, going to throw that in the car later on today.
08-08-2012
Alright the new wizaired is installed. Jesus ****ing christ ZZP needs to get better fitmit on that thing,
Ran out of daylight to get finalized pictures. but here are some during install
08-09-2012
Quaility was clearly job 1. Or they expect you have a slightly different setup? maybe they expect the maf inside the box?
On intercooler routing. Lowest point on your FMHE is what feeds into your pump that should be located at the same height or lower than that exit from the FMHE. Something to consider is that you won't have a lot of fluid in the system the way you describe it. Many have found the running hose through the bump tubes gives you about an extra gallon or two. Pickup a hose that is larger and fits over your IC hose to slip over and use as a buffer to any sharp edges etc.
Keep in mind on the pics, this is not your routing, this is Bonnie. Giving you the sharp edge info though
I then thought about movement over time and put a zip ties on the smaller hose right where I wanted the larger to stay put. This worked well and didn't restrict the smaller hose at all.
08-09-2012
By the looks of it, did you just shove the MAF into the TB inlet? no coupling or seal or anything???
Originally Posted by AmericanSoldier
08-10-2012
Sheffer..I believe he was "test fitting"
08-10-2012
KK that makes sense, I was like woah... wait... what?
Originally Posted by AmericanSoldier
08-10-2012
Yeah it was a test fit, Whats the proper way that is recommended for the MAF?
08-11-2012
that might of been what was causing my stalling issue when the RPM's drop below 1000
08-12-2012
So what's keeping this beast off of the road?
Originally Posted by TLSheff
08-12-2012
It needs a tune, and also needs to figure out why its stalling now that the transmission leak is fixed
08-16-2012
could you take a picture of your overflow tank for your collant and where it is located i had to ditch mine when i did my intake and im looking to get another one again.
08-16-2012
Doug..there was just a post or two on this in the last day. Give the search bar a whirl.
08-17-2012
I belive the fix for the guy BillBoost is talking about was a fuse. Also the guy said one of his ground wires was touching his hood when he shut it couseing it to ground out. The guy's post is in "BoostenGTP's Ride".
08-17-2012
Grounding to ground.. how's that cause any issue?
09-06-2012
Anyone know why it would be stalling if not kept above 1000 rpms? wasnt doing that before i got the leak fixed..
09-06-2012
What is the IAC count look like? Is it not idling or stalling in gear?
09-06-2012
not idling, unless you give it gas and keep the RPM's over 1000.
The car still has not been tuned yet. i just finished doing the RNC security
| « Previous Thread | Next Thread » |
| Tags for this Thread |
| Bookmarks |
Bookmarks |
