|
|
06-07-2012
hey i just got a AEM uego wideband today and i was jus curious where the hell im supposed to be mounting the O2 sensor at on the headers, i dont know if it matters but i have speed daddy headers on it too. ive tried lookin around a little and havent really seen much but im sure i prolly overlooked it or somthin. all helps appreciated thanks.
06-07-2012
18" downstream from the downpipe is the 'recommended' place to mount the oxygen sensor.
before the cat if you have one.
06-07-2012
I have mine in place of the ds o2. I've been told its to far away though
06-07-2012
If your welding a bung in, just put it in the crossover pipe near the rear head, easy to get to and easy to wire up.
06-07-2012
yea i gotta weld in a new bung, and is it really good to just shove in the crossover pipe? cuz if so holy crap would that be easier. do you just put it like right under the throttle body or? also FoSHO99 i was curious if you know of anyone over in that area with a tuner that could tune my car for me? im originally from that area and movin back soon once i find a job back there, my dad lives in wyoming,ia and i come back often.
06-07-2012
PM theothernick I think he's from IOWA.
06-07-2012
ok kool kool thank you i was gunna say right now im livin in des moines but ill drive anywhere in iowa. sooo thank you lol..... but ALSO it really is ok to shove that sensor in the crossover pipe?
06-07-2012
I wouldn think that place would be very accurate? If youre running a cat I think right in front of it would be the best spot imo.... when I put my AEM in I put it right before the last bend in the downpipe of my headers...
06-07-2012
yea deff not running a cat i have speed daddy headers with the catless dp. there alot like the slp with that nice lil low hangin u-bend in it. would it be good to jus throw it in there right after that u-bend on the down pipe or would you go right before the u-bend?
06-07-2012
I went right before my bend... maybe other widebands are different but I dont think these are as accurate if they are right there in the crossover...
06-07-2012
That sounds like a prime location to me lol it'll be just as easy there as in the crossover sincee I got a lift to work withlol
06-07-2012
Thanks for all the help as usual guys very much appreciated
06-07-2012
do a little more reading dont just take my advice for real... it may work fine either way or I may have done it wrong... just saying the suggestions of more are better than one or two...
06-07-2012
I put mine right here.
06-07-2012
I put mine on the top of that.
Less likely to make love with a rock.
06-07-2012
I love rocks.
06-07-2012
thats a good place...
06-07-2012
The front bank is not going to be much different from the rear bank, less likely to be a leak before the sensor and overall easier. You can do what you want but it's not going make or break you from 5hp.
Stainless Steel Headers w/ Downpipe
ZZPerformance - Stainless Headers #ZZ-304HDR-38
06-07-2012
Thats flipin awsome thank you x20 for the pic and the extra input thats the general area I was thinkin but its deff nice to get those pics and know others are puttin it there too, thanks again everyone ur a life saver cuz I was pretty well clueless before this lol
06-07-2012
I also e-mailed Zzp just to see wut they say for location too so once they tell me ill post again with wut they say just incase anyone else out there cares to know too.
| « Previous Thread | Next Thread » |
| Tags for this Thread |
| Bookmarks |
Bookmarks |
