Thread: Aeroforce??

Anyone using this how did you hook it up. Because you have to use 3 wire connector right? Did you run it to a fuse and if you did what one? i tried it and it wouldnt power on. Yes I took the red jumper off, then put it back on and pluggeg in only the obdII port and it would power up then turn off and the 2 lights would flash.

dont they have some form of troubleshooting in their manual?

yea I hooked it up like it said i looked at the one online because the one it came with was really brief and didnt have much in it, I think it might be the wire running it to the fuse because i used the radio one

I dont get why this isnt working. I ran it to the radio fuse and it will turn on for a few seconds then shut off and the 2 red lights start blinking does anyone know whats going on, or how exactly you installed yours? any help would be awesome

I'm having the same problem. Please let me know if you figured it out

I have 4 Aeroforces and dont have a problem running them.

I would guess if you bought it used you may have the wrong Version for your car

I figured it out lol, the wire running to the fuse was bad

Originally Posted by bstuby

i just looked at the torque app for the droid and it had 0 bad complaints on it. i think i might get it instead and save myself hundreds of dollars

read up first. IIRC KR isn't a supported parameter. On our cars if you can't scan for KR, you may as well burn the $39 you'd be spending on the scanner and app.

99% of the time it's wiring.

I think it is on 2001+ plus that the obd2 doesn't have the power wire on it. Therefore you have to wire it separately and read the instructions to get the jumpers right if needed. If it powers up then goes off after a few seconds/moments it is most likely getting signal from the obd2 but not any power.

I would use some 16-18 guage wiring and run the power to the power drop harness under the glovebox, possibly tucked in up to the right. It will have a label on it and should label what each wire is. I would also run the ground to harness as well.

see, i bought mine from another member and when i turn on the car all i get is 2 blinking lights, if i unplug it and plug it back in it works fine

i didnt get a manual so ive been trying to figure out whats up with the online version

i have a 99 GT so the guage should get power from the OBDII, which is the only thing its plugged into

any ideas? im still new to aeroforce

Originally Posted by CTKGP09

see, i bought mine from another member and when i turn on the car all i get is 2 blinking lights, if i unplug it and plug it back in it works fine

i didnt get a manual so ive been trying to figure out whats up with the online version

i have a 99 GT so the guage should get power from the OBDII, which is the only thing its plugged into

any ideas? im still new to aeroforce

Just put mine in today. you need the 3 wire conector and the red wire goes to power. then you need to take the Jumper off the back of the Gauge then put it in the obd port

Or you can come over to my house and Ill hook it up for you.

Yea just get a fuse tap kit and run it to the radio fuse in your glove box

ok easy enough, ill wire it with the other guages, i just need to get that harness then

josh, i was in akron a few days ago, ill prob be up at my buddys apartment in the valley one day this week again

Originally Posted by CTKGP09

see, i bought mine from another member and when i turn on the car all i get is 2 blinking lights, if i unplug it and plug it back in it works fine

i didnt get a manual so ive been trying to figure out whats up with the online version

i have a 99 GT so the guage should get power from the OBDII, which is the only thing its plugged into

any ideas? im still new to aeroforce

mine was a 99 gt to lol well still is but i just have a constant power wire connected to one of the 3 wires and it works good.