Thread: Another Where's This Plug Into Thread

Results 1 to 5 of 5
  1. #1 Another Where's This Plug Into Thread 
    SE Level Member
    Join Date
    Jul 2016
    Location
    Ft. Worth, Tx
    Posts
    13
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Ok, I'm changing the CV on a 2006 Grand Prix GT 3.8 SC. There is a single blue wire that runs with the oil pressure sending unit below the P/S pump. I unplugged the Oil sending, then later noticed the other " blue single wire" unplugged. I would like to get it plugged in before I get everything back together. Any ideas? Thanks.
    Reply With Quote  
     

  2. #2 Re: Another Where's This Plug Into Thread 
    GTX Level Member QUICKSILVER462's Avatar
    Join Date
    Jun 2009
    Location
    HUDSON
    Posts
    1,133
    Thanks (Received)
    3
    Likes (Received)
    8
    Dislikes (Received)
    0
    Sounds like it could be a knock sensor wire. There are two knock sensors, one on each side of the block between the core/freeze plugs. Each knock sensor has one wire going to it.
    On my car (2000 GTP) one sensor has the wire straight from the engine harness, the other sensor has a sub harness that is like an extension to reach the engine harness.
    I would be a good idea to check your knock sensors and make sure they are connected, it is unknown to me if a disconnected knock sensor would through a code or not.
    Reply With Quote  
     

  3. #3 Re: Another Where's This Plug Into Thread 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,921
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    sounds like the knock sensor harness wire. you need to get under the car look up between the trans and engine pans and you'll see the knock sensor. you'll need some long needle nose pliers to get that plug back on it.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  4. #4 Re: Another Where's This Plug Into Thread 
    SE Level Member
    Join Date
    Jul 2016
    Location
    Ft. Worth, Tx
    Posts
    13
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Thanks guys. I'll check em.
    Reply With Quote  
     

  5. #5 Re: Another Where's This Plug Into Thread 
    SE Level Member
    Join Date
    Jul 2016
    Location
    Ft. Worth, Tx
    Posts
    13
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Thanks again. It was the knock sensor.
    Reply With Quote  
     

Similar Threads

  1. HELP. WHAT SPECIFIC SPARK PLUG NON FOULER WILL THREAD IN o2 BUNG
    By MrDniceL36 in forum 3.8L V6 Naturally Aspirated (L36)(L26)
    Replies: 2
    Last Post: 10-23-2014, 02:21 PM
  2. 2008 Base model plug and plug wire swap
    By MS1227 in forum 04+ Specifics
    Replies: 2
    Last Post: 12-06-2012, 06:14 PM
  3. so i've read the big bad brake thread...and drunkie's ctsv thread
    By Couch in forum Brakes/Suspension/Chassis
    Replies: 9
    Last Post: 07-21-2012, 12:37 PM
  4. stock antenna plug to universal plug?
    By kind153 in forum Audio, Security & Visual Electronics
    Replies: 5
    Last Post: 01-08-2012, 10:25 PM
  5. plug gap
    By NoTyme in forum 3.8L V6 Naturally Aspirated (L36)(L26)
    Replies: 3
    Last Post: 06-16-2009, 06:11 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •