Thread: Do I need to replace vacuum booster?

Results 1 to 8 of 8
  1. #1 Do I need to replace vacuum booster? 
    SE Level Member
    Join Date
    Oct 2010
    Location
    MD
    Posts
    55
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Hi:

    Re: 1999 Grand Prix 3.8L

    Here's what's happening:

    • Brake pedal goes to the floor, no resistance at all
    • No leaks under car
    • Reservoir was empty; filled it, pumped pedal and level dropped, but still no visible leaks.



    From what I have read, this is most likely an issue with the master cylinder seal, and fluid disappearing without leaks means that the fluid is leaking into the vacuum booster.

    Question: Does this mean I will have to also replace the booster when I put in the new master cyl?

    Thanks!
    Reply With Quote  
     

  2. #2 Brake line(s) leaking 
    SE Level Member
    Join Date
    Oct 2010
    Location
    MD
    Posts
    55
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Sorry, the master cyl and booster were not the problem.

    I found a leak in the line(s) where they go through a bracket just below the ABS module. It's going to be a bear to replace the line(s). Here are some pics.



    Given that the car is 22 years old (but a goldie!), what is my best course of action? Should I splice new line where the corrosion has occurred, replace the entire section or replace all brake lines?
    Reply With Quote  
     

  3. #3 Re: Do I need to replace vacuum booster? 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    im willing to bet all the lines that run to the back of the car are about shot to hell. be best to buy a brake line kit and a fuel line kit and replace all the old lines.

    once you start touching them that old and rusty anther leak will start due to playing with them all.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  4. #4 Replacing brake lines '99 Grand Prix 
    SE Level Member
    Join Date
    Oct 2010
    Location
    MD
    Posts
    55
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by Scottydoggs View Post
    im willing to bet all the lines that run to the back of the car are about shot to hell. be best to buy a brake line kit and a fuel line kit and replace all the old lines.

    once you start touching them that old and rusty anther leak will start due to playing with them all.
    Scotty: As usual, you're right. I've searched for brake line kits and they look more than worth the risk of a future problem. Given the age of my car, I was considering the steel ones rather than stainless. Do you agree, or should go big if I'm going through all the trouble?

    Now the important question: Can do this job without a lift? I have a hydraulic jack and 2 sturdy jack stands. Will it be possible by jacking up the front end, doing the front wheels and connecting the front half of the rear lines and then moving to jacking up the rear end and completing the rear wheels. The car has ABS, so will I be able to disconnect the module and get a bit more flexibility to maneuver?

    Thanks again.
    Reply With Quote  
     

  5. #5 Re: Do I need to replace vacuum booster? 
    GT Level Member mguzzo's Avatar
    Join Date
    Dec 2007
    Location
    Buffalo NY
    Posts
    483
    Thanks (Received)
    8
    Likes (Received)
    27
    Dislikes (Received)
    0
    I would use stainless over mild steel anytime. If you have 4 jack stands you could probably get the car up high enough to work on it all at once
    --
    "Silver Bullet" 98 GTP Coupe: Stock, rust free, and broadsided.
    Old '98 GTP Coupe: VS Cam, 3.0, S2IC, 42.5#, TOGs, N*/LQ4, Corsa. it once ran a 13 flat
    Older '98 GTP Sedan: Pullied, rockered, SSIC, etc. Stock 14.33 @ 96.5 / PB: 13.89 @ 101
    Reply With Quote  
     

  6. #6 Re: Do I need to replace vacuum booster? 
    GT Level Member
    Join Date
    Apr 2014
    Location
    commerce twp,mi
    Posts
    291
    Thanks (Received)
    3
    Likes (Received)
    21
    Dislikes (Received)
    0
    im thinking this isnt a trailer queen. with what im reading in the amount of rust, id go with copper. its real easy to bend and flare. might cost a bit more but the job is quick.
    i replaced fuel lines on an '08 cobalt last friday. fuel filter to firewall. it took longer to get the old lines out than to install new copper. not factory match bends but pretty dam close
    08 grand prix NA3800
    Reply With Quote  
     

  7. #7 Re: Do I need to replace vacuum booster? 
    SE Level Member
    Join Date
    Oct 2010
    Location
    MD
    Posts
    55
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by tomsteve View Post
    im thinking this isnt a trailer queen. with what im reading in the amount of rust, id go with copper. its real easy to bend and flare. might cost a bit more but the job is quick.
    i replaced fuel lines on an '08 cobalt last friday. fuel filter to firewall. it took longer to get the old lines out than to install new copper. not factory match bends but pretty dam close
    Thanks for the suggestion, tomsteve. Sounds like the pros of Cu-Ni are ease of bending and flaring, cons are easily kinked and over tightening fittings. Definitely something I'll consider. Going to take the old lines off first and see how hard that is and how involved the bends under the hood are going to be (my car has an ABS module.) Wasn't thinking of the fuel line but probably should do that too. Is the fuel line the same diameter?
    Reply With Quote  
     

  8. #8 Re: Do I need to replace vacuum booster? 
    GT Level Member
    Join Date
    Apr 2014
    Location
    commerce twp,mi
    Posts
    291
    Thanks (Received)
    3
    Likes (Received)
    21
    Dislikes (Received)
    0
    Quote Originally Posted by jammy View Post
    Thanks for the suggestion, tomsteve. Sounds like the pros of Cu-Ni are ease of bending and flaring, cons are easily kinked and over tightening fittings. Definitely something I'll consider. Going to take the old lines off first and see how hard that is and how involved the bends under the hood are going to be (my car has an ABS module.) Wasn't thinking of the fuel line but probably should do that too. Is the fuel line the same diameter?
    they only kink by misuse. ive used copper right off of abs units no problem. its pretty simple to not over tighten. what the pros do is not torque the **** out of the fittings right off the get go. no need to go all he man on em. just tighten them. check for leaks and tighten a little more as required.

    fuel line should be a larger diameter than brake lines.
    08 grand prix NA3800
    Reply With Quote  
     

Similar Threads

  1. Do I need to replace vacuum booster?
    By jammy in forum General Grand Prix Discussion
    Replies: 0
    Last Post: 04-23-2021, 12:30 PM
  2. Brake Vacuum Booster Wiggles - Is This Normal?
    By sparkydog in forum Brakes/Suspension/Chassis
    Replies: 2
    Last Post: 05-13-2015, 07:34 AM
  3. Supercharger vacuum tree\booster cap
    By Booba5185 in forum Wanted To Buy - Parts
    Replies: 8
    Last Post: 05-31-2013, 10:04 PM
  4. 2002 GP GT 3.8L Small Vacuum Line Connected to Brake Booster Fitting At Upper Intake
    By LoveMyGPGT in forum 3.8L V6 Naturally Aspirated (L36)(L26)
    Replies: 8
    Last Post: 08-23-2010, 07:51 PM
  5. brake booster vacuum problem
    By comongoose in forum Brakes/Suspension/Chassis
    Replies: 12
    Last Post: 03-20-2009, 12:46 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •