Thread: Building new FE3's, mount question

Results 1 to 6 of 6
  1. #1 Building new FE3's, mount question 
    I can't car too good. SaukRapids's Avatar
    Join Date
    May 2016
    Location
    MN
    Posts
    1,054
    Thanks (Received)
    3
    Likes (Received)
    3
    Dislikes (Received)
    0
    GM's parts diagrams show a wedge shape spacer in with the mount, like #4 on this -



    Will I need to buy that wedge thing, GM 22167000, or will it be in with the mounts depending what I buy? These look slightly different shape than those pictured in Rockauto's mount kits.

    They're only about $8/ea so it's an easy order if I need em. Thanks for any input!
    Reply With Quote  
     

  2. #2 Re: Building new FE3's, mount question 
    I can't car too good. SaukRapids's Avatar
    Join Date
    May 2016
    Location
    MN
    Posts
    1,054
    Thanks (Received)
    3
    Likes (Received)
    3
    Dislikes (Received)
    0
    I just went ahead and bought these off ebay. I don't know if they're getting scarce. Well, I'm not even sure I'll need them for that matter.

    There was also a couple "Shield" items I wasn't too sure about. I found the OE bellows, so I may need them.

    It seems like it should be very straightforward, but it just isn't that simple finding the parts to piece these together.

    I plan on making a list of the required AC Delco part numbers for this project. Might even do a write-up, amount of free time pending.

    Part #'s so far:

    Strut - GM 506273
    Dust Shield(?) - GM 22189840
    Wedge/Isolator - GM 22167000
    Bellows - GM 901083
    Reply With Quote  
     

  3. #3 Re: Building new FE3's, mount question 
    GrandPrix Junkie spazzz's Avatar
    Join Date
    Nov 2012
    Location
    Madison
    Posts
    3,328
    Thanks (Received)
    3
    Likes (Received)
    8
    Dislikes (Received)
    0
    You wont need the angle spacer if you get Monroe mounts. I had bad luck with groaning using those.

    I would buy the AC Delco professionals and re-use the plastic spacer.
    It looks like most mount kits manufacturers think you will re-use the old spacer.
    It does get pricey if you are replacing 100,000 original isolators, etc.

    Make sure you add more grease to the bearings i

    Anyway here is a pic I found of a Monroe assembly.

    Reply With Quote  
     

  4. #4 Re: Building new FE3's, mount question 
    I can't car too good. SaukRapids's Avatar
    Join Date
    May 2016
    Location
    MN
    Posts
    1,054
    Thanks (Received)
    3
    Likes (Received)
    3
    Dislikes (Received)
    0
    That pic will be useful later, and I actually didn't think of grease yet either. Thanks on both accounts.

    Think I'm gonna pull one side, take the spring off and see what's layin there. Then I can compare with what I plan to order and ask questions.

    Just wanna make sure it's all here.
    Reply With Quote  
     

  5. #5 Re: Building new FE3's, mount question 
    GrandPrix Junkie spazzz's Avatar
    Join Date
    Nov 2012
    Location
    Madison
    Posts
    3,328
    Thanks (Received)
    3
    Likes (Received)
    8
    Dislikes (Received)
    0
    I checked my Rockauto order from when I did it a few years ago.
    This is all I needed to get it done,front and back.
    The Monroe strut mate kits are probably your best deal. I didn't grease mine before install.
    I learned a lesson. I replaced them with Duralast from Autozone just because I decided to remedy it one day. Those I greased.

    Reply With Quote  
     

  6. #6 Re: Building new FE3's, mount question 
    I can't car too good. SaukRapids's Avatar
    Join Date
    May 2016
    Location
    MN
    Posts
    1,054
    Thanks (Received)
    3
    Likes (Received)
    3
    Dislikes (Received)
    0
    Ok, I have most the parts on their way here. spazz, you mentioned grease. I gather the bearing needs it, but did you grease any other areas?

    Read maybe do the insulators too? Asking cus a friend just did them and has an awful noise when turning the strut by hand.

    Thanks again!
    Reply With Quote  
     

Similar Threads

  1. Radiator Mount Question
    By TheManiac in forum Brakes/Suspension/Chassis
    Replies: 2
    Last Post: 12-13-2011, 05:57 PM
  2. transmission mount question?
    By hardrocrick in forum General Tech Discussion
    Replies: 6
    Last Post: 08-11-2011, 02:47 PM
  3. Engine mount question
    By goldgp in forum General Tech Discussion
    Replies: 4
    Last Post: 09-24-2010, 08:47 PM
  4. Motor mount question
    By goldgp in forum General Tech Discussion
    Replies: 4
    Last Post: 08-16-2010, 07:42 AM
  5. Mount question
    By kjohnson in forum Audio, Security & Visual Electronics
    Replies: 9
    Last Post: 07-02-2009, 02:15 AM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •