Thread: Stumped and have no access to a scaner

Results 1 to 12 of 12
  1. #1 Stumped and have no access to a scaner 
    SE Level Member
    Join Date
    Dec 2010
    Location
    Noble, Oklahoma
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    ok i lleft my scanner at home and went on vacation, now i have cel and my car is cutting out bad under a load. first #2 coil pack went out that fixed it. then i was driving and started cutting bad drives/idles fine just cant accelerate. any ideas what it could be? i already checked the firing order to make sure i didn't swap a plug wire. no shop around here has a scanner and oreillys doesn't offer one to use just to buy. worst case senario i buy another one. any advice will be greatly appreciated
    Boostin To A City Near You
    Reply With Quote  
     

  2. #2 Re: Stumped and have no access to a scaner 
    SE Level Member Mike Kopstain's Avatar
    Join Date
    Jun 2009
    Location
    Chicago, IL
    Posts
    117
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Does the check engine light blink when you're accelerating? If you were having coil pack issues I almost wonder if you're having a connection issue there. My supercharger belt sliced through a wire once and it left just enough wire there that the plug would fire under no/ low loads but couldn't get enough current to fire under any kind of throttle application.

    Thinking about shopping with ZZP or the other guys? - Order with us instead and we'll give you a 5% off coupon code for your next order! Click here to learn how!

    Like us on Facebook!
    Reply With Quote  
     

  3. #3 Re: Stumped and have no access to a scaner 
    SE Level Member
    Join Date
    Dec 2010
    Location
    Noble, Oklahoma
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by Mike Kopstain View Post
    Does the check engine light blink when you're accelerating? If you were having coil pack issues I almost wonder if you're having a connection issue there. My supercharger belt sliced through a wire once and it left just enough wire there that the plug would fire under no/ low loads but couldn't get enough current to fire under any kind of throttle application.
    Yes it does. i checked my wires but i will re check again. everytime i accelarate and even stay in it ( cause sometimes it's not that bad ) the cel will blink
    Boostin To A City Near You
    Reply With Quote  
     

  4. #4 Re: Stumped and have no access to a scaner 
    The Blue One blueguy's Avatar
    Join Date
    Jun 2008
    Location
    Dirtyzville, Missery
    Posts
    31,287
    Thanks (Received)
    1
    Likes (Received)
    2
    Dislikes (Received)
    0
    Autozone and Orielly's scan cars for free...are you sure you don't have a vacuum leak. Sounds like a "T" fitting is being blown off under boost. Check those.
    Sold WBody's: '03 Blue GTP/'98 Green GTP/'98 Silver GT/'05 GXP
    '99 Chevrolet Silverado Classic Z71 4x4 - K&N Intake/Gibson Exhaust #TRUCKTHINGS
    '12 Buick Regal Turbo - ZZP CAI/20% Tint/HID's
    '89 Ford Mustang LX Notchback - LM7 5.3, 4L80, 9", HX40
    '04 Chevrolet Corvette MRM A4/LS1 - TSP LT's, 3"O/R X, AFE S2 CAI
    Reply With Quote  
     

  5. #5 Re: Stumped and have no access to a scaner 
    SE Level Member
    Join Date
    Dec 2010
    Location
    Noble, Oklahoma
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    No autozone here. Oriellys doesn't scan cars here either. I know if i was home it would be easier to deal with. as for a vaccum leak i will re-check, i will go over all of them
    Boostin To A City Near You
    Reply With Quote  
     

  6. #6 Re: Stumped and have no access to a scaner 
    SE Level Member
    Join Date
    Dec 2010
    Location
    Noble, Oklahoma
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    sprayed everything down with carb cleaner. No vac leaks. just put new plugs and wires on and it's not that either. any other suggestions?
    Boostin To A City Near You
    Reply With Quote  
     

  7. #7 Re: Stumped and have no access to a scaner 
    SE Level Member
    Join Date
    Dec 2010
    Location
    Noble, Oklahoma
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    I double checked the connection with the coil packs and there all getting fire. A lot of fire.
    Boostin To A City Near You
    Reply With Quote  
     

  8. #8 Re: Stumped and have no access to a scaner 
    The Blue One blueguy's Avatar
    Join Date
    Jun 2008
    Location
    Dirtyzville, Missery
    Posts
    31,287
    Thanks (Received)
    1
    Likes (Received)
    2
    Dislikes (Received)
    0
    Now your kinda at the point I think where you need to know which code it is. Most of the time a flashing CEL is going to pull a P0300 which is just a random misfire. Could be a bad injector as well...
    Sold WBody's: '03 Blue GTP/'98 Green GTP/'98 Silver GT/'05 GXP
    '99 Chevrolet Silverado Classic Z71 4x4 - K&N Intake/Gibson Exhaust #TRUCKTHINGS
    '12 Buick Regal Turbo - ZZP CAI/20% Tint/HID's
    '89 Ford Mustang LX Notchback - LM7 5.3, 4L80, 9", HX40
    '04 Chevrolet Corvette MRM A4/LS1 - TSP LT's, 3"O/R X, AFE S2 CAI
    Reply With Quote  
     

  9. #9 Re: Stumped and have no access to a scaner 
    SE Level Member Mike Kopstain's Avatar
    Join Date
    Jun 2009
    Location
    Chicago, IL
    Posts
    117
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by MoBoost View Post
    Yes it does. i checked my wires but i will re check again. everytime i accelarate and even stay in it ( cause sometimes it's not that bad ) the cel will blink
    Take off the supercharger belt and see if you have that issue. You're getting a misfire under load which could indicate any number of things. I'm kind of curious about the state of your Ignition Control Module.

    Here's a silly question, when you swapped coils, did you put a coil in with the same numbers? I've seen people swap coils and then plug the wires into the original coils which would now be wrong since the coils were swapped.

    Thinking about shopping with ZZP or the other guys? - Order with us instead and we'll give you a 5% off coupon code for your next order! Click here to learn how!

    Like us on Facebook!
    Reply With Quote  
     

  10. #10 Re: Stumped and have no access to a scaner 
    Donating Users nascartech's Avatar
    Join Date
    Mar 2009
    Location
    Abbotsford, British Columbia, Canada
    Posts
    1,017
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    question i have for you is whats mods and what size pully do u have
    01 GTP is3 cam 130 springs double roller 60lb injectors lq4 maf headers 4000 stall lowered
    sold 97 GTP stock
    Sold 2001 gp gt ssm90 plog dp 3.8 208 whp 265 at the crank 14.8 1/4
    Reply With Quote  
     

  11. #11 Re: Stumped and have no access to a scaner 
    GXP Level Member offroadfury6's Avatar
    Join Date
    Aug 2008
    Location
    Fayetteville, NC
    Posts
    2,677
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by Mike Kopstain View Post
    Take off the supercharger belt and see if you have that issue. You're getting a misfire under load which could indicate any number of things. I'm kind of curious about the state of your Ignition Control Module.

    Here's a silly question, when you swapped coils, did you put a coil in with the same numbers? I've seen people swap coils and then plug the wires into the original coils which would now be wrong since the coils were swapped.
    ummm what do u mean? when u buy new coil packs, they're not even numbered, it doesn't matter which coil pack goes where...and you said they pluged the wires into the original coils soooooo huh?
    2011 Honda Civic EX-L - Leather/Sunroof/LOADED!
    2009 Saturn Aura XE - I got shift paddles!!!
    '98 Olds Cutlass - Good, Dependable
    '06 GP GT S/C - Traded it in
    Reply With Quote  
     

  12. #12 Re: Stumped and have no access to a scaner 
    GT Level Member RegalGS98s's Avatar
    Join Date
    Oct 2010
    Location
    NJ
    Posts
    369
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by offroadfury6 View Post
    ummm what do u mean? when u buy new coil packs, they're not even numbered, it doesn't matter which coil pack goes where...and you said they pluged the wires into the original coils soooooo huh?
    Think he means some people get coil packs with the different numbers and instead of putting the wires where they should, they go by the numbers labeled on the coil packs. When I bought my GTP, the numbers where mixed up cause the previous owner must of got coils from a junkyard or something.
    SMGPFC #0330 - 3.25, Intercooled, Custom Tune, 1.84rr, LS6 Springs, roller timing chain, SLP Headers, Borla Exhaust, built Trans, B&M Trans Cooler, home cut poly uppers, gapless rings, N* TB, Ported heads.
    Soontocome: CAM?, Custom modified M112, home poured Poly Engine and Trans mounts
    Reply With Quote  
     

Similar Threads

  1. Can't access site from pc
    By Slick2500 in forum Forum Bugs/Suggestions
    Replies: 8
    Last Post: 11-20-2010, 12:19 AM
  2. Cannot access chat.
    By rynoman03 in forum Forum Bugs/Suggestions
    Replies: 14
    Last Post: 11-09-2010, 05:50 PM
  3. engine forum access
    By Sandman in forum Forum Bugs/Suggestions
    Replies: 5
    Last Post: 08-01-2010, 07:37 PM
  4. access to gauges???
    By kjclawson in forum General Tech Discussion
    Replies: 8
    Last Post: 08-16-2009, 02:51 AM
  5. Anyone have access or do CNC Machine work?
    By SD GTP in forum Off Topic Discussion
    Replies: 2
    Last Post: 03-22-2008, 10:35 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •