Thread: Trouble codes after tranny install

Results 1 to 9 of 9
  1. #1 Trouble codes after tranny install 
    GrandPrix Junkie SDGTP99's Avatar
    Join Date
    May 2009
    Location
    Wichita
    Posts
    3,085
    Thanks (Received)
    1
    Likes (Received)
    5
    Dislikes (Received)
    1
    Just got my tranny installed and car seems to run and drive fine bar 2 things. I'm getting DTC's P0700 and P2764. TCC pressure control solenoid low voltage. And my traction control says its needs service. I've checked and cleaned all my connections and couldnt find any frayed wires or bad connections. I'm at a bit of a loss. Or can this be caused by ground wires? I think when I put the tranny back in 4 ground wires ended up sharing the same spot. Idk I need some here, please.
    OverKilled, HAI, Ported Throttle body, Ported intake, ZZP DP, Magnaflow, BMR ta's, GMPP STB's, CCS springs, tinted tailights, roof rails, TEP cool'r, G8 hood. Glass Gearbox.
    Reply With Quote  
     

  2. #2 Re: Trouble codes after tranny install 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    this a used tranny? or a rebuilt unit by the shop?

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  3. #3 Re: Trouble codes after tranny install 
    GrandPrix Junkie SDGTP99's Avatar
    Join Date
    May 2009
    Location
    Wichita
    Posts
    3,085
    Thanks (Received)
    1
    Likes (Received)
    5
    Dislikes (Received)
    1
    Just had 2nd gear clutch replaced. I installed the tranny myself.
    Reply With Quote  
     

  4. #4 Re: Trouble codes after tranny install 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    they may have broken the harness inside the cover. its a brittle pos. can break and not know it.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  5. #5 Re: Trouble codes after tranny install 
    GrandPrix Junkie SDGTP99's Avatar
    Join Date
    May 2009
    Location
    Wichita
    Posts
    3,085
    Thanks (Received)
    1
    Likes (Received)
    5
    Dislikes (Received)
    1
    Oh dang! Well, Its going back to them on Monday. Guess I'll find out then.
    Reply With Quote  
     

  6. #6 Re: Trouble codes after tranny install 
    GrandPrix Junkie SDGTP99's Avatar
    Join Date
    May 2009
    Location
    Wichita
    Posts
    3,085
    Thanks (Received)
    1
    Likes (Received)
    5
    Dislikes (Received)
    1
    Had to get a new Pressure Solenoid. 😑
    Reply With Quote  
     

  7. #7 Re: Trouble codes after tranny install 
    GTX Level Member wstefan20's Avatar
    Join Date
    Aug 2017
    Location
    Raytown, MO
    Posts
    1,152
    Thanks (Received)
    33
    Likes (Received)
    63
    Dislikes (Received)
    1
    Owch. This is why I refuse to just "fix the one issue" and bolt it back up. I always at bare minimum replace all clutches, inspect, and replace all solenoids. All solenoids are something like $80 so it's cheap insurance against having to rebuild it down the road. At that point, an entire master rebuilt kit is only $500 including the solenoids, so I almost never do a partial rebuild for this exact reason.

    Glad to hear they are taking care of it though. I know installing these transmissions are a pita so I feel your pain having to pull it again. At least you can save money there!
    Reply With Quote  
     

  8. #8 Re: Trouble codes after tranny install 
    GrandPrix Junkie SDGTP99's Avatar
    Join Date
    May 2009
    Location
    Wichita
    Posts
    3,085
    Thanks (Received)
    1
    Likes (Received)
    5
    Dislikes (Received)
    1
    Mmm feels good to have the GXP back, and it runs great now. Sadly the traction control lights are still screaming at me. I'll figure it out. Eventually
    Reply With Quote  
     

  9. #9 Re: Trouble codes after tranny install 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Check your wheel bearings.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

Similar Threads

  1. Couple of Codes after Tranny install. Hmmm
    By Brian99SE in forum 1997-2007 4 speed Automatic (4T65E) (4T65E-HD)
    Replies: 2
    Last Post: 06-28-2012, 11:10 PM
  2. Trouble codes after header install
    By dsmuts in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 11
    Last Post: 08-06-2011, 04:13 PM
  3. trouble codes
    By grand2000prixgtp in forum Off Topic Discussion
    Replies: 2
    Last Post: 10-16-2009, 07:35 AM
  4. trouble codes
    By grand2000prixgtp in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 12
    Last Post: 08-19-2009, 02:32 PM
  5. trouble codes
    By BADAZGTP in forum Forum Bugs/Suggestions
    Replies: 6
    Last Post: 07-26-2008, 10:59 AM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •